IMPORTANT
Insert the battery into the quadcopter and connect the
plug. The two indicators will begin flashing. Place the
quadcopter on a flat surface.
Important:
Be sure the surface is flat and level. The
quadcopter needs to calibrate it’s orientation.
PLEASE PRACTICE SIMULATED FLIGHT BEFORE ACTUAL FLYING
Before you are familiar with the unit, please don't pilot it . Read the instruction carefully to get
familiar with the direction controls.
1. Checking that propellers are securely attached to the motors. Pull the throttle down to prevent takeoff.
2. Place quadcopter in a clear open field and point the tail towards yourself.
3. Practice operating the control sticks (as shown below), and repeat practicing “Throttle
high/low”, “ Left/right ”, “Forward/backward”, and “bank left/right”.
4.Strong impacts can jam the motors, using a long flat nose plier to unjam to rotor.
5.The simulation flight practice is very important, please keep practicing until you are comfortable with the controls.
After turn on the quadcopter
the LED indicators keep
flashing but the quadcopter
does not respond.
Transmitter and receiver
fail pairing
•
Sync the remote control
and copter
(refer to P.7)
• F
ully charge the battery
1.The blade isn’t fully installed
2.Rotor blade deformation
3.Rotor blade not match code
• Ch
ange blade
• Correct the level refer to P6
• Replace the main wing
• Replace the main motor
The quadcopter still keeps
turning after trimming the
rudder trim, or inconsistent
speed during left/right turns.
1. This product is only suitable for users overthe age of 8. Piloting this quadcopter will be dificult at the
beginning. We recommend be occampanied by an experienced pilot at first.
2. This product is designed with high-tech electronics and mechanical parts. Do not fly near people.
Improper operation can result in injury or property damage. We will not accept any responsibility for
this.
3. We will not take any responsibilty for accidents during the operation of this device.
4. Contact cutomer service for help if you have any problems with the device.
1.Checking the surroundings before flying.
2.Do not let the plane fly out of sight when flying.
3.Do not let the child play alone, play together with adult.
4.Please make sure, there is no other player use the same frequency at the same area.
Do not fly in these areas.
Cautions:
QUADCOPTER COMPONENTS
PACKAGE CONTENTS
REMOTE CONTROL FUNCTIONS
The propeller system is a precision instrument that may need to be repaired or replaceed from
time to time for optimal flight function. Crash landing from high-speed aerial flights may cause
damage to propeller blades.
1.The aircraft has four blades, two white colors on front, and two black colors on back (see the
diagram below).
2.When replacing the propeller blades, make sure to match both the color of the blade and the
indication letter on the blade.
3.Replace broken blades with the correct blade.
Charge with our dedicated charger
.
RECHARGEABLE BATTERY:
This Quadcopter uses a Li-Poly rechargeable battery.If battery no longer stays charged,dispose
of battery properly according to local disposal requirements.
CONTROLLER BATTERIES:
Remote control requires 2”AAA”batteries (not included).Please read the important battery safety
warning below.
●
Do not mix alkaline,standard (carbon-zinc) and rechargeable betteries (Nickel Metal Hydride).
●
Do not mix old and new batteries.
●
Non-rechargeable batteries are not to be recharged.
●
Rechargeble batteries are to be removed from the item before being charged (if removable).
●
Rechargeble batteries are only to be charged under adult supervision.
●
Exhausted batteries should be removed immediately and must be recycled or disposed of
properly according to state or local government ordinances and reulations.
●
The supply terminals are not to be short-circuited.
●
Only batteries of the same or equivalent type as recommended are to be used.
●
Batteries are to be inserted with the correct polarity (see inside booklet for diagram).
●
Do not dispose batteries in a fire-batteries may leak or explode.
BATTERY WARNINGS
The LED will be on continuously while the quadcopter is on. When it is low on
power the indicator will blink. Please land the quadcopter.
SYNCING THE REMOTE CONTROL & QUADCOPTER
STEP 1
STEP 2
FLIGHT ADJUSTMENT AND SETTING
CAUTION
CAUTION
FLIGHT ADJUSTMENT
AND NOTICE
FOR
BEGINN
E
RS
Check if the screws and blades are firmly tightened
Check if the transmitter and helicopter are fully charged.
Make sure that no people or obstructions are in the vicinity.
You must first practice hovering to fly safely, this is a basic
flight action(meaning keep the helicopter in mid air in a fixed position)
Please stand approximately 6ft diagonally behind the helicopter.
1. The throttle is on the left hand, push the throttle a little up to raise the copter to
your line of sight then pull down a little to let the quadcopter slowly down to the
floor. Repeat until you can easily and quickly control the altitude.
2.Hovering flight practic: Raise the quadcopter to a certain height then hover at
that altitude.
3.Try increasing and decreasing the altitude quickly this time while still
maintaining control.
1. Use the right stick to practice moving forward and backwards.
2. Use the left and right stick to practice turns and banking.
Slowly raise the throttle stick and observe just as the helicopter lifts off the ground if it
leans in a direction. You can use the trim to correct this action.
1. Adjust
ment of Left/Right trim
Just before the quadcopter lifts-off, the nose leans left/right.
When it leans right adjust the trim to the left side.
When it leans left adjust the trim to the right side.
2. Adjust
me
nt of Forwards/Backwards trim
Just before the quadcopter lifts-off, the nose leans forward/backwards.
When it leans forwards adjust the trim down.
When it leans backwards adjust the trim up.
3. Adjust
ment of Roll trim
Just before the quadcopter lifts-off, the body rolls left/right.
When it rolls right adjust the trim to the left side.
When it rolls left adjust the trim to the right side.
If a MicroSD card is not installed the
LEDs will flash 5 times. When a
MicroSD card is intalled the leds will
stay illuminated.
Micro SD card sold seperately.
8G
（
FAT&FAT32 format
）
INSTALL A MICRO SD CARD
CAMERA / VIDEO OPERATION
The remote control can control the quadcopter’s camera.
Photo Mode: Press the camera button to take a picture. The LED
on the quadcopter will flash once to confirm it took a picture.
Video Mode: Press the video button to start recording a video.
The LED on the quadcopter will blink slowly while it is recording.
Press the video button again to stop recording.
To access the photos and video you will need a MicroSD card
reader.
The maximum capacity of MicroSD card is 64G(FAT format)
TROUBLE SHOOTING DURING FLIGHT
Solution
No response after the
battery is connected to
the quadcopter.
Main rotor continues to
spin after landing
Helicopter rotor spins but
unable to take off.
The helicopter still keeps
turning after rudder triming
or inconsistent speed during
left/right pirouette.
1. The blades haven’t been
installed in the right place.
2. Rotor blade deformation
3. Didn’t calibrate the flight.
1. Replace the main wing
Replace the main motor
2. Change blade
3. Correct the level refer to P6
Throttle stick not on the
lowest position
1.Check whether the blade
assembled correctly or not.
2.Helicopter battery depleted.
Make sure the Throttle stick is
on the lowest position
Check whether it is low power
Charging the helicopter
The quadcopter shifts
forwards/ backwards.
The trim is not even.
• Trim the elevator back to center.
• Restart the remote control.
1.Rotor blade turns off
2.Rotor blade deformation
1
.
Change replacement rotors
2
.
Tighten the Rotors
Can not fly the helicopter
after crashing
QUADCOPTER COMPONENTS
FLIGHT CHARGING
CONTROLLER INSTRUCTION
CAUTIONS
FLIGHT ADJUSTMENT AND SETTINGS
INSTALLING A MICROSD CARD
CAMERA OPERATION
SYNCING THE REMOTE CONTROL
AND THE QUADCOPTER
REPLACING THE PROPELLER BLADE
GD-90C
High-voltage power lines
Rainstorm and thunderstorm
Near the railway
Roads and nearby places Forests and rivers
High winds
The places of Crowds
Rotate
Direction
7
8
Camera
Camera board
9
10
2
2
2
2
Positive rotor blades
Reverse rotor blades
Positive rotor
Reverse rotor
Battery charge
As shown in the figure, push the rocker of the remote
control to the position in the lower right corner at the
same time. At this time the indicator light of the aircraft
flashes and then loosens the remote control, and the
indicator light is always on and the calibration is complete.
WARNING
When not in use for a long time, please take out the remote
control battery and keep it properly.
Note: If the remote control battery is not removed, the long
storage will cause the leakage of the battery and damage
the remote control device.
Throttle
1
.
On/off
(1)On(After put on the battery, R/C is in sleep model,indicator extinguish when off)
Short Press the ON/OFF, the remote control enters the normal mode of work, the buzzer is short
sound one beeping, and the power indicator is fading.
(2)Power off: long press the ON/OFF, the buzzer is short sound two beeping, the power indicator
is out and the remote control is off.
2
.
Turning
When the remote control and the aircraft are pairing the code, move the turning rocker to left and
right,the aircraft will turn left and right.
3
.
Forward and backward
When the remote control and the aircraft are pairing the code, move the rocker to forward and
backward, the aircraft will fly forward and backward.
4
.
Left and right
When the remote control and the aircraft are pairing the code, move the rocker to left and
right,the aircraft will fly left and right.
5
.
Fine-tuning function
The aircraft can be stabilized by adjusting the direction of the aircraft, in the opposite direction of
flight.
6
.
Headless mode
Short press the button to enter headless mode. The vehicle’s flying direction will be the same as
the demand of controller,no matter where the head is .
7
.
Speed/Stunt
Short press the button to adjust the speed. There are three speed levels.You will hear a beep
sound while adjusting . Beep one for level 1 ,beep two for level 2, beep three for level 3. The
higher the level ,the faster the speed.Long press the button for stunt .The beeper will keep.
ringing.
8
.
Take photo/video
short press the button to take photo,long press the button to take video,press again to finish
video
9
.
One key take off and one key landing
In the fixed high mode,after press the one key take off and one key landing buttons,
automatically aircraft up to one meter from the ground level hover, trigger buttons again, aircraft
flying will fall to the ground stops automatically
10
.
One key to return
Short press the button for one key to return . Press again to finish return .
11
.
Calibration
(1) if the aircraft is drifting to one side during takeoff, it can be calibrated to make the flight more
stable
(2)calibration method: the aircraft is placed on the horizontal surface, and the two rocker of the
remote control is pushed to the lower right corner, when observed the indicator light flashes on
the aircraft, release the remote control rocker, indicating that it has been calibrated.
(note: the aircraft should be kept at the horizontal surface. During calibration, the aircraft will not
be able to riot . After the calibration is completed, the indicator light will stop flash quickly).
12
：
Low Volatage Warning
：
When the voltage of battery is lower than 2.5V
，
power light will blink ,which means you have to
change the battery. Meanwhile, a “beep beep”sound will send from the buzzer
，
which means
you have to stop flying the vehicle.
Caution
During the flight, the indicator light of the aircraft is slow to flash while the remote control makes a
"beep beep", indicating that the battery voltage is insufficient and please land down to recharge the
battery.
Mobile phone adapter
：
Output: 5V
Charging current: 1-2A.
1.Take off the battery from the vehicle. Connect the battery with a USB cable . Plug the USB cable into
a mobile phone adapter or a computer.
2.The Charging Indicator will blink when charging. The Charging Indicator will turn OFF when fully
charged .
400
Stable, flexible, 3D to roll easily
Stable, flexible, 3D to roll easily
2M
After you skilled above basic movements, you can play some of the breathtaking tumbling action.
First, the aircraft flew more than 2 meters’ height; Press the key rollover, then push the stick of
forward/backward, or left /right to top then release the aircraft can roll over.
Speed/Stunt
Take photo/video
Headless mode
The direction rocker
The throttle rocker
Front and back fine-tuning
Left and right fine-tuning
On/off button
One key to return back
One key to take off
One key to land
3.7V 400mAh
Li-Po Battery
controller
1x USB cable
4x spare blades
1x Small screwdriver
