Apevia X-Telstar Jr Скачать руководство пользователя

Страница: 1 / 13

7. Temperature probe setup:

6.1 Daisy chain the fans to be regulated
      using the fan speed controller. Con-
      nect male to female ends and plug
      the last male end into the fan
      controller connector labeled ‘OUT-
      PUT’. The male end of the connector
      with 7 wires(2 yellow, 2 red, 3 black)
      is then routed to the power supply.

6.2 Use the fan controller knob on the
front panel to regulate the airflow
and fan noise.

6. Case fan setup:

7.3 Should you opt to monitor your
      hard-drive’s operating temperature,
      place the probe on the hard-drive’s
      surface. Thermal tape should be
      used for best results.

Note: You may also leave a sensor loose in the chassis in order to monitor
the ambient system temperature. DO NOT place the sensor directly on the
CPU as it will damage the sensor.

7.2 Place the probe on any ‘fin’ of the
      CPU’s heatsink and tape in place.
      Thermal tape should be used for
      best results.

7.1 Locate device temperature probe.

5. Connect case leads to motherboard:

5.1 Locate the top panel leads. Your
      motherboard user’s manual will
      provide schematics. The triang-
      ular markings      on the leads
      indicate positive wires.

5.2

Locate front panel leads. LED leads

      are located near the right-side panel.
      The Power/Reset/Speaker leads can
      be accessed by removing the left
      panel. Refer to your motherboard
      user’s manual for placement schem-
      atics.

(Remove right-side panel to better access wiring.)

7.4 Monitor system temperatures from
the front panel LCD.

10. USB/1394/Audio cable pin assignments:

9. Complete the installation:

9.3 With all components properly installed, gently
      return side panels to their original positions
      and replace all screws. Congratulations! You
      have completed assembly of the X-Telstar Jr.

8. LED display features:

8.2 The 5V/12V monitor displays the current voltage
values of the 5 and 12 volt rails respectively.
Red areas indicate very low/high voltages.

8.1 The fan monitor displays the percentage
of total RPMs currently being used.

8.4 The “Voice Unit” display allows you to
monitor dynamic audio gain and
gain reduction levels.

8.3 TMPE1 displays the current temperatures
of the device being monitored.

9.1 Connect the two Power LEDs. The Apevia logo LED
is powered by a 2-pin connector. (blue/white wire.)

9.2 Plug in the LED, which is powered by a 2-pin
Molex consisting of a black/red wire pair.

2. Motherboard installation:

4.2 From the outside rear of the case,
push PCI slot cover(s) toward the
inside of the chassis.

4.1 First, remove the PCI slot covers.
      Firmly press point A with thumb,
      while pulling point B with index
      finger to open the latch.

3.5 Align rails with hard-drive bay and
insert.

4. Install PCI components:

3.1 To install an optical or floppy drive,
      first remove the metal shield that
      sits behind each drive bay cover.
      This must be done from the inside
      of the case. Next remove the drive
      bay covers by using a screwdriver,
      and forcing them out from behind.

3.4 Attach 1 mounting rail to each side
of each hard-disk drive.

3.2 For 5 1/4” drives, align the device
      with the drive bay and insert. Do
      the same for 3 1/2” drives using
      the two lower drive bays (one bay
      is accessible from the front of the
      case, the other must be accessed
      from inside the case.

3.3 Slide the blue drive-rail forward
      and push the clamp downwards
      to engage locking mechanism.
      No screws are necessary, but
      can be used optionally on opti-
      cal and floppy drive bays.

4.3 Read your PCI expansion card’s
      documentation. Install PCI card
      into correct slot for your card
      type (x1, x16, etc.).

3. Install 3½” and 5¼” drives

4.4 Once the card is seated firmly,
      return latch to the initial position.
      A ‘click’ will be heard when fully
      engaged.

2.2

If your motherboard included an

      IO shield, you must remove the
      X-Telstar Jr.’s IO shield. Use
      thumbs or other object to push
      shield inward (cover area with a
      cloth to avoid injury from metal
      edges!).

2.1 Refer to the motherboard holes
      index for standoff placement for
      your motherboard type. A full
      ATX (12”x9.6”) board will use
      notches A1-A9. Some mother-
      boards may not use all notches.
      Use any notches that line up
      with your motherboard.

2.3 Put standoff screws in place. Align
      motherboard with standoffs and
      mount to case. This ATX mother-
      board (12”x8.3”) only used notches
      A1-A6. M8 was also used since it
      lined up.

1.4

Install power supply on top of

mounting ledges.

1.6 Fasten screws.

1.5 Make sure that the power supply is
correctly installed, and that screw
mount points are aligned.

NOTE: Touch an unpainted metal section of the chassis to discharge
static electricity before handling PC components. An anti-static wrist
strap should also be worn to further minimize the possibility of damage.

1.3 Likewise for the window version;
      grab the notch on the left panel
      and pull to release.

1. Power Supply installation:

1.1 Remove thumbscrews from the
rear of the X-Telstar Jr.

NOTE:

CPU and memory installation is not covered in this

manual. Please refer to each components’ documentation
for instructions.

25cm Fan version

Window version

Motherboard installation................................1

Install 3½” and 5¼” drives

..........................3

Install PCI components................................5