General
Instructions
General
Instructions
Standard Assembly
Vertical Configuration - Insert Replacement
1.
To remove Clear Lens, first place magnet over Locking Pin located on
top right hand corner of sign. If pin does not lift, shift clear cover to the
left and try again.
2.
Shift Clear Lens to the
right
. For smaller signs the suction cup may
be used to do this. For larger signs, use your hands as shown.
3.
Attach Suction Cup Tool to the left side of the Clear Lens and press to
engage. Pull outward while holding Clear Lens edge.
4.
After new paper display is inserted into holder, reverse steps 1-3.
Note: When replacing clear cover, make sure non-glare
finish side is facing outward.
Standard Assembly
Horizontal Configuration - Insert Replacement
1.
To remove Clear Lens, locate Locking Pin on top left hand side of sign.
If your frame does not feature a Locking Pin, go to steps 3-4 below.
2.
Place Magnet Tool over pin at the top left corner of sign, thus removing
security pin from the slot.
3.
Affix Suction Cup Tool to lower center of Clear Lens and press inward
to engage. Lift clear cover upward into the space previously blocked
by the locking pin.
4.
Pull Clear Lens outward from lower center to remove. Insert new paper
display, and reverse steps 1-3.
Note: When replacing clear cover, make sure non-glare
finish side is facing outward.
APCO
388 Grant Street, SE, Atlanta, Georgia USA 30312-2227 Toll Free 877-988-APCO (2726) www.apcosigns.com IS428
APCO
388 Grant Street, SE, Atlanta, Georgia USA 30312-2227 Toll Free 877-988-APCO (2726) www.apcosigns.com IS428
VERY IMPORTANT!
The key to optimal performance and successful installation of your FullView product is to carefully follow the instructions within this
guide which can be reviewed within several minutes.
Large Assembly
Horizontal Configuration Insert Removal & Replacement
1.
Apply Large Suction Cup Tool to bottom/center of the non-glare Lens,
shift Lens up and pull outward from frame.
You may find that your graphic is held in place with a strip of low-tack
tape that’s attached to the core of the sign frame. This tape will not
damage your sign insert but is very helpful to hold the digital print
steady while inserting the non-glare Lens into the frame.
Frames with 4-Side Capture
If your sign features the aluminum capture extrusions on the left/right
sides, those will need to be removed before you can remove the Lens.
2.
Use a 1/16” hex wrench to loosen the screws from both left and right
sides of the extrusions.
3.
Once the screws are loose, the capture extrusions can be removed.
1
11/1/16
11/1/16
Large Assembly
Installation - Mechanical Fasteners (MF) Only
1.
Counter sunk mounting holes are located in each corner of the frame’s
core. Using a level, position the frame on the wall surface in the desired
location and use a pencil or similar to transfer the hole pattern to the
wall. Pre-drill the wall at those marked locations.
2.
Use #8 or #10 flat head fasteners to affix the frame to the wall.
Anchors and/or other special fasteners need to be considered depending
upon the exact conditions of the installation location and wall surface.
General Care & Maintenance
FullView Products are designed to provide years of trouble-free service,
but proper care is essential.
Always clean by wiping with a soft, lint-free, damp cloth, taking care to
wipe gently, not rub. Using a very mild solution of liquid hand soap and
lukewarm water is optional. If cleaning with liquid and/or damp cloth, take
care not to make contact with any subsurface paper sign displays as they
may be damaged by the moisture.
IMPORTANT! Avoid using products such as window cleaners, liquids
containing ammonia, scouring compounds, or solvents of any kinds (i.e.
alcohol, acetone, etc.) as they may damage the sign finish.
IMPORTANT REGARDING ADA SIGNS! ADA (tactile & Braille) signs are
only suited for interior, climate-controlled environments. Regular exposure
to high humidity and temperature extremes may result in sign
deterioration.
Retention Clips with Larger Standard Assembly Signs
If your sign is 17”h x 17”w or larger, it likely features a clear plastic
Retention Clip (as in the images to the right) at the Top/Bottom Center of
the frame for Vertical Configurations, or at the Right/Left Center for
Horizontal Configuration signs. This Clip helps retain larger Lenses within
the frame and also ensures compression on the subsurface graphics.
If your sign features Retention Clips, they must be removed in order to
remove the sign insert from the frame.
1.
Remove the clip by pressing down the small flange. Do not pry off. The
clip will tilt and the back angle is exposed. See Fig. 1. Now rotate the
clip to release from the narrow rail.
2.
To replace, push clip directly on the narrow aluminum rail, the clip will
snap over the angle edge. See Fig 2.
Insert Removal & Replacement
Insert Removal & Replacement / Installation / Care & Maintanence
1
2
1
2
1
2
1
2
3
3
4
3
4
2
