background image

EN-H15-G

HORN SPEAKER

The Apart-Audio EN-H15-G is a powerful horn speaker made of UV and impact resistant ABS (RAL 7035 equivalent), (UL94V0), equipped with a compression driver and 
a multitap 100 volt transformer, all certified according EN 54-24. Ip66 makes it the ideal choice for industrial applications.
The unit is equipped with a ceramic speaker line connector block, junction box, thermal fuse and stainless installation bracket. The unit can be used as a low impedance 
speaker by setting the power selector switch to the 20 ohms position. Lo-Z impedance and power: 20 ohms, 15 watts.
The highlights are: Ip66, weather resistant ABS, junction box, lo-Z and 100 volt.

Not included: cable gland for the cable from the power amplifier to the junction box.

Technical specifications

Speaker type

compression driver

Dimensions (Ø x d)

209 x 272 mm

Colour

RAL 7035

100 volt transformer power taps

15/7.5/3.75/1.87 watts

Lo-Z impedance

20 ohms

Lo-Z power

15 watt

Frequency response (-10 dB, IEC268-5)

454 - 10400 Hz

Frequency range

400 - 12000 Hz

Dispersion angle -6 db, 500 Hz / 1 kHz / 2 kHz / 4 kHz

360° / 130° / 74° / 35° 

SPL 1W / 1m (IEC268-5)

100.5 dB

SPL 1W / 4m (IEC268-5)

88.5 dB

SPL Pmax / 4m (IEC268-5)

100.3 dB

SPL Pmax / 1m (IEC268-5)

112.3 dB

Sensitivity EN54-24, 1W / 4m

IP classification

66

Chassis material

ABS plastic

Mounting instructions

1. Install the bracket and junction box on a wall or ceiling.
2. Connect the speaker cable to the power amplifier.
3. Set the power selector switch at the rear of the speaker as required. 

EN 54-24

certified

Safety precautions

Warranty info 

Legal info 

  

 Keep this manual for future reference.

 When making the hole in your mounting panel to mount the Apart

  speaker, make sure there is sufficient clearance behind the panel 

  (no obstructions  like A/C channels, power lines etc, ...).

 Take care of your speaker wires, they should be free of damage. Damaged

  speaker wires may result in poor sound quality and can damage amplifiers.

 Only use accessories specified by the manufacturer.

 Make sure the mounting panel can support the speaker's weight.

 Use a sufficient amount of speakers to avoid dead spots.

 No main power shall be connected to the loudspeakers, doing so will

  damage the speaker.

 This apparatus should only be serviced by qualified personnel. If not

  serviced by qualified personnel, warranty may be void.

 Use cable of the right gauge, certainly for long runs.

 Use cables with clear color indication and maintain polarity   throughout

  the whole system.

 Avoid loud feedback from microphones, this can damage your speaker.

 Please check the unit's condition after unpacking. If the outside of the

  carton box has been damaged, inform your shipper immediately.

Apart Audio warrants this product to be free of defects in material and 

workmanship for a period of one year for parts and for a period of one year 

for labor from the date of original end-user purchase. This warranty is valid 

only for the original end-user and cannot be transferred.

During the warranty period Apart Audio or one of its authorized service 

partners shall either repair or replace any product, free of charge, that proves 

to be defective on inspection by Apart Audio or its authorized service 

representative.This warranty does not include, damages or product faults due 

to abuse, misuse or faulty installation.

Audioprof nv

Industriepark Brechtsebaan 8 bus 1, 2900 Schoten - Belgium

Company names, product names and trademarks are property of their 

respective owners. Apart-Audio specifications are subject to change without 

notice.

Certificate No.: 1438/CPD/XXXX

Please note: to obtain the frequency response requested in EN54-24,
an equalizer has to be integrated into the signal path.

77.3 dB

Отзывы: