Anton Paar DMA 4100 M Скачать руководство пользователя страница 38

Страница: 38 / 152

9 Installing Optional Input/Output Devices

C76IB003EN-E

9.2

USB Flash Drive

•

Insert a USB flash drive or another USB mass storage device into one of the

four USB interfaces that are located on the left and rear of the instrument.

TIP

Some older USB flash drives are formatted in the super floppy way. These are not

compatible with your DMA M instrument. USB flash drives formatted in the

standard hard disk way are compatible.

9.3

Printer

You can use an RS-232 printer via RS-232 interface or an office printer (PCL

compatible) via USB interface or via local network. After connecting the printer to

the instrument, register the printer in the menu

"Setup > Control Panel > Printer

Management"

For a list of tested printers, refer to "www.anton-paar.com/generation_m-tested-

printers".

9.3.1

Connecting a Printer

To connect an RS-232 printer

1. Connect the printer (Mat. No. 44737 or 93362) to the RS-232 interface

(COM) of the instrument using the cable that is supplied together with the

printer.

2. If you use an RS-232 printer which is not supplied by Anton Paar, set the

communication settings on the printer properly (see Appendix A.3).

To connect an office printer (not supplied by Anton Paar) via USB interface

•

Connect the printer to a USB interface of the instrument.

To connect an office printer (not supplied by Anton Paar) via local network

You can connect your instrument and a PCL compatible printer (or an Epson

Stylus D120) via Ethernet to your local network.

1. Connect the instrument via Ethernet interface to your local network.

2. Tap <Menu> and select

"Setup > Control Panel > Network"

3. If your network server has DHCP functionality, activate "Obtain an IP

address automatically (DHCP)", then tap <Next> and <OK>.

4. If your network server has no DHCP functionality, deactivate "Obtain an IP

address automatically (DHCP)" and enter the correct "IP Address", "Subnet

Mask", "Default Gateway", and tap <Next>.

Содержание DMA 4100 M

























































































































































Результаты поиска

Содержание DMA 4100 M

Отзывы:

Похожие инструкции для DMA 4100 M

Бренды по названию

Популярные бренды

Anton Paar DMA 4100 M, Инструкция по эксплуатации

Результаты поиска

Содержание DMA 4100 M

Отзывы:

Похожие инструкции для DMA 4100 M

Бренды по названию

Популярные бренды