Anton Paar DMA 4100 M Скачать руководство пользователя страница 118

Страница: 118 / 152

Appendix B: Measuring Special Samples

118

C76IB003EN-E

B.2

Special Filling Techniques

Bubbling samples

If the sample to be measured tends to form gas bubbles, degas it before the

measurement (see Appendix B.1).

If this is not possible, introduce the sample at a temperature higher than the

measuring temperature.

You can also put the density meter at a slight angle by means of proper spacers

below the right side of the DMA M to allow the bubbles to escape due to buoyancy.

Suspensions and emulsions

Suspensions or emulsions may tend to separate in the measuring cells, giving

incorrect results. Leave such samples in the measuring cell as briefly as possible.

Prethermostat them before filling.

It may help to put spacers below the left legs of DMA M, thus putting it at an angle

to counterbalance the separation force generated by the oscillation of the

measuring cell.

Highly viscous samples

Highly viscous samples can be heated up to lower the viscosity. Always heat the

sample to a temperature that is approx. 15 °C higher than the measuring

temperature, which can be 90 °C maximum.

Pastes

Paste-like materials like toothpaste or tomato ketchup can be filled by syringe.

Inject these kinds of samples into the measuring cell by pushing the plunger very

slowly and continuously.

If the samples have a very high viscosity, you can fill them into the syringe by

pulling the plunger completely out of the syringe, filling it from the back using a

spoon and then mounting the plunger again.

Liquids in aerosol cans

For the quality control of aerosol cans, you can use the Anton Paar Aerosol

Adapter (Mat. No. 74650) to fill the liquid safely and conveniently into your

DMA M. For details, see the Aerosol Adapter instruction manual.

Gases

It is possible to measure gases with the DMA M. For details, contact your local

Anton Paar representative and ask for the respective application report and the

necessary accessories.

Содержание DMA 4100 M

























































































































































Результаты поиска

Содержание DMA 4100 M

Отзывы:

Похожие инструкции для DMA 4100 M

Бренды по названию

Популярные бренды

Anton Paar DMA 4100 M, Инструкция по эксплуатации

Результаты поиска

Содержание DMA 4100 M

Отзывы:

Похожие инструкции для DMA 4100 M

Бренды по названию

Популярные бренды