manualshive.com logo in svg

ANTAIRA LMP-C602G-SFP-bt-T-V2, Руководство по оборудованию

Поделиться
Скачать
ANTAIRA LMP-C602G-SFP-bt-T-V2 Скачать руководство пользователя страница 6

Antaira Technologies - Industrial Ethernet Switches 
LMP-C602G-SFP-bt-V2 Series - Hardware Manual - v1.0 

 

1 Overview 

Antaira Technologies’ LMP-C602G-SFP-bt-V2 series is a 6-port industrial compact gigabit PoE++ 

managed Ethernet switch embedded with 4*10/100/1000Tx Ethernet ports that support IEEE 802.3bt for 

a maximum of 90W/port and 2*100/1000 dual rate SFP slots for fiber connections. The 

LMP-C602G-SFP-bt-V2 series is a fully manageable light layer 3 Ethernet switch that is pre-loaded with a 

user-friendly web management console design. There are also two wide operating temperature models 

for either a standard temperature range (STD: -10°C to 65°C) or an extended temperature range (EOT: 

-40°C to 75°C). 

1.1 Product Hardware Features 

System Interface and Performance 

-

All RJ45 ports support Auto MDI/MDI-X Function 

-

Embedded 4*10/100/1000Tx (90W/Port) RJ45 ports and 2*100/1000 SFP slots 

-

Store-and-forward switching architecture 

-

8K MAC address table 

-

Supports 9.6Kbytes jumbo frame 

-

4Mbits memory buffer 

Product Input 

-

DC 48~55V redundant, with a 6-pin removal terminal block 

-

Max. current: 4.1A 

-

Max. PoE output: 240W 

-

Relay contact: 24VDC, 1A resistive 

-

It is recommended to use a UL listed industrial power supply 

-

For bt PoE application(s), the recommended power input should be not less than 53VDC 

Operating Temperature 

-

Standard operating temperature model: -10°C to 65°C 

-

Extended operating temperature model: -40°C to 75°C 

Case / Installation 

-

IP40 protection metal housing 

-

DIN-Rail and wall-mount design 

1 

Содержание LMP-C602G-SFP-bt-T-V2





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды