ANTAIRA LMP-1802G-M12-10G-SFP-67-110 Series Скачать руководство пользователя страница 22

Страница: 22 / 26

Antaira Technologies - Industrial Ethernet Switches

LMP-1802G-M12-10G-SFP-67-110 Series - Hardware Manual - v1.0

4 Hardware Installation

4.1 Installation Steps

This section will explain how to install the industrial Ethernet switch:

Caution:

This device is intended for indoor use.

Attention:

Cet appareil est destiné à une utilisation en intérieur.

Caution:

The device is intended to be installed in an industrial control enclosure and panel.

Attention:

L'appareil est destiné à être installé dans une armoire de commande et un panneau industriels.

Installation Steps

1. Unpack the industrial Ethernet switch from the original packing box.

2. To hang the industrial Ethernet switch on a wall, please refer to the Mounting Installation section.

3. Power on the industrial Ethernet switch and then the power LED light will turn on.

●

If you need help on how to wire power, please refer to the

Power Inputs

section.

●

Please refer to the

LED Indicators

section for LED light indication.

4. Prepare the M12 cable for Ethernet connection.

5. Insert one side of the M12 cable into the switch's Ethernet port and on the other side into the networking device’s

Ethernet port. The Ethernet port’s (L/A) LED on the industrial Ethernet switch will turn on when the cable is

connected to the networking device.

●

Please refer to the

LED Indicators

section for LED light indication.

6. When all connections are set and the LED lights all show normal, the installation is complete.

Содержание LMP-1802G-M12-10G-SFP-67-110 Series



























Результаты поиска

Содержание LMP-1802G-M12-10G-SFP-67-110 Series

Отзывы:

Похожие инструкции для LMP-1802G-M12-10G-SFP-67-110 Series

Бренды по названию

Популярные бренды

ANTAIRA LMP-1802G-M12-10G-SFP-67-110 Series, Руководство по оборудованию

Результаты поиска

Содержание LMP-1802G-M12-10G-SFP-67-110 Series

Отзывы:

Похожие инструкции для LMP-1802G-M12-10G-SFP-67-110 Series

Бренды по названию

Популярные бренды