ANTAIRA LMP-1002G-SFP Series Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 21

ANTAIRA LMP-1002G-SFP Series Скачать руководство пользователя страница 15

Antaira Technologies - Industrial Ethernet Switches

LMP-1002G-SFP Series Hardware Manual V1.2

11

Caution:



The wire gauge for the terminal block should range between 12 ~ 24AWG



If only using one power source, jumper Pin 1 to Pin 5 and Pin 2 to Pin 6 to
eliminate power fault alarm.

2.10 Grounding Note

Grounding and wire routing help limit the effects of noise due to electromagnetic interference (EMI).
Run the ground connection from the ground screw to the grounding surface prior to connecting
devices. The grounding screw symbol is shown blow in Figure 2.15.

Figure 2.15 - Grounding screw

Caution: Using a shielded cable achieves better electromagnetic compatibility.

3. Mounting Installation

3.6 DIN-Rail Mounting

The DIN-Rail is pre-installed on the industrial

Ethernet switch from the factory. If the DIN-Rail

is not on the industrial Ethernet switch, please

see Figure 3.1 to learn how to install the DIN-

Rail on the switch.

Follow the steps below to learn how to hang the industrial Ethernet switch.

1. Use the screws to install the DIN-Rail bracket on the rear side of the industrial Ethernet switch.

Figure 3.1

The Rear Side of the Switch and DIN-Rail Bracket

«
...
13
14
15
16
17
...
»

Содержание LMP-1002G-SFP Series






















Отзывы:

Нет отзывов