manualshive.com logo in svg

Anritsu VectorStar MN469 C Series, Руководство по обслуживанию, Страница: 26 / 78

Поделиться
Скачать
Anritsu VectorStar MN469 C Series Скачать руководство пользователя страница 26

3-5 S-Parameters Measurements Verification

Chapter 3 — Performance Verification

3-6

PN: 10410-00730  Rev. D

MN469xC Series Multiport Test Set MM

Special Precautions

When performing the procedures, observe the following precautions: 

•

Minimize vibration and movement of the system, attached components, and test cable.

•

Clean and check the pin depth and condition of all adapters, test port cables, calibration components, 

and impedance transfer standards.

•

Pre-shape the test cable so as to minimize its movement during calibration and measurement activities.

Procedure

1. 

Set up the MS464XX VNA and MN469XC Test Set per the MN469xC Series Test Set Installation Guide, 
part number 10410-00737. 

2. 

Power up the test set and VNA per the 

Power Up Sequence

 of the MN469xC Series Test Set Installation 

Guide. Allow the system to warm up at least 90 minutes.

3. 

Using the GPIB interface cable to connect the external computer/controller to the VNA rear panel system 

GPIB connector. It is the upper GPIB port labeled IEEE488.2 GPIB.

4. 

Power up the external computer/controller. 

5. 

Install the female to female phase equal insertable adapter from the calibration kit to Port 1 of the 
MS464xx VNA. This converts Port 1 from a male test port to a female test port.

6. 

Install the female to female phase equal insertable adapter from the calibration kit to Port 3 of the 
MN469xC. This converts Port 3 from a male test port to a female test port.

7. 

Install the Test Port Cable to Port 2 of the MS464xx VNA and then the male to female phase equal 
insertable adapter from the calibration kit to the open end of the cable.

8. 

Install the Test Port Cable to Port 4 of the MN469xC and then the male to female phase equal insertable 

adapter from the calibration kit to the open end of the cable.

9. 

Run the MS464XX System Verification software.

10. 

Insert the USB memory device (also called a “USB flash drive”) supplied with the verification kit to an 
available USB port on the external computer/controller. Set the data location of the verification software 
to the USB memory device when prompted.

11. 

Follow the directions displayed on the computer to perform calibration with the appropriate calibration 
kit.

12. 

Follow the directions on the computer to perform measurements of impedance transfer standards of the 
appropriate verification kit.

13. 

Pass/Fail status of the measurements is displayed on the computer. The software can also provide a hard 

copy printout of the measured data, measurement uncertainties, and the impedance transfer standards 
used.

14. 

If the verification fails, check the connectors of the VNA test ports, calibration kit devices, the impedance 

transfer standards, and test port cables for damage, cleanliness, and proper connection and torquing. 
Also check the phase stability of the test port cables. These are the most common causes for verification 
failures.

Содержание VectorStar MN469 C Series















































































Отзывы:

Нет отзывов