manualshive.com logo in svg

Anritsu MU181800A, Руководство по эксплуатации

Поделиться
Скачать
Anritsu MU181800A Скачать руководство пользователя страница 37

 

6.2  Devices Required for Performance Tests 

6-3 

6.2  Devices Required for Performance Tests 

Before starting performance tests, warm up the MU181800A/B and the 
measuring instruments for at least 30 minutes.    Table 6.2-1 shows the 
devices required for performance tests. 

Table 6.2-1    Devices required for MU181800A/B performance test 

Device 

Required Performance 

Synthesizer 

Generating frequency: 

0.1 to 12.5 GHz (MU181800A) 

0.1 to 14.0 GHz (MU181800B) 

0.1 to 14.1 GHz (MU181800B-005) 

Output amplitude: 

0.4 to 2.0 Vp-p 

Sampling oscilloscope 

Electrical interface: 

50 GHz or more band 

Trigger signal source 
(M MU181020A, or 

1/64 divider supporting 14 

GHz) 

Generates trigger to observe the sampling oscilloscope waveform 

 

Note: 

Before starting the performance tests, warm up the device under 
test and the measuring instruments for at least 30 minutes and 
wait until they become sufficiently stabilized, unless otherwise 
specified.    Additional conditions are required for maximum 
measurement accuracy: measurements must be performed at room 
temperature, fluctuations of AC power supply voltage must be 
small, and noise, vibration, dust, and humidity must be 
insignificant. 

 

Содержание MU181800A



















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды