Anritsu 3659 Скачать руководство пользователя страница 92

Страница: 92 / 160

3-17 High-Band Calibration – Port 3/Port 4

Using the 2300-580-R Software with VectorStar ME7838D4

3-42

PN: 10410-00327 Rev. D

3659 0.8 mm Cal/Ver Kit & 2300-580-R PVS UG

3-17 High-Band Calibration – Port 3/Port 4

During this procedure, the high-band portion of the VNA is calibrated with a full 12-term SSST
(Short-Short-Short-Thru) calibration. In

Section 3-16 “Low-Band Calibration – Port 3/Port 4” on page 3-39

, the

low-band portion of the VNA is calibrated with a full 12-term SOLT (Short-Open-Load-Thru) calibration.

Procedure

The

0.8 mm Verification Install Adapter

dialog box appears.

Install a F-F adapter on VNA Port 3 so that a Female connector is available to the operator.

Install a F-M adapter on VNA Port 4 so that a Male connector is available to the operator.

When ready to proceed, click

. The

VNA Calibration: Step 1 of 5

dialog box appears.

Connect the Male Cal Kit Isolation Device to VNA Port 3.

Connect the Female Cal Kit Isolation Device to VNA Port 4.

When ready to proceed, click

Figure 3-59.

Anritsu 0.8 mm Verification Dialog

Figure 3-60.

VNA Calibration: Step 1 of 5 Dialog

Содержание 3659

































































































































































Результаты поиска

Содержание 3659

Отзывы:

Anritsu 3659, Руководство пользователя, Страница: 92 / 160

Результаты поиска

Содержание 3659

Отзывы: