annke DN41R Скачать руководство пользователя страница 13

Страница: 13 / 106

Digital Video Recorder User Manual

Figure 2. 4 Configure Signal Input Type



Picture is for reference only,please consult with the real products.



The AHD signal input is supported by some series DVR only.



For some series DVR, Each two video channels are grouped in sequence, e.g., CH01 and CH02, CH03 and

CH04…, and the two channels in the same group must be connected with the same type of video source, i.e.,

the analog or HD-TVI or AHD video input. And for some series DVR, each four video channels are grouped

in sequence.



In the live view interface, when there is no video signal of the analog channel, the corresponding connectable

video signal type message can be displayed on the screen.

2.3.2 Using the Wizard for Basic Configuration

By default, the Setup Wizard starts once the device has loaded.

Figure 2. 5 Start Wizard Interface

Operating the Setup Wizard:

The Start Wizard can walk you through some important settings of the device. If you don’t want to use the

Содержание DN41R











































































































Результаты поиска

Содержание DN41R

Отзывы:

Похожие инструкции для DN41R

Бренды по названию

Популярные бренды

annke DN41R, Руководство пользователя

Результаты поиска

Содержание DN41R

Отзывы:

Похожие инструкции для DN41R

Бренды по названию

Популярные бренды