
- 1 -
I
NSTRUCTION MANUAL
Automatic Spray Guns
Be sure to observe warning s and cautions in this instruction manual.
If not, it can cause paint ejection and serious bodily injury by drawing organic solvent.
Be sure to observe following
marked items which are especially important.
Indicates a potentially hazardous situation which, if not avoided, may result in serious injury or loss
of life.
Indicates a potentially hazardous situation which, if not avoided, may result in minor
or moderate injury or property damage.
Indicates notes which we ask you to observe. The safety precautions in this
instruction manual are the minimum necessary conditions. Follow national and
local regulations regarding fire prevention, electricity and safety as well as your own
company regulations.
Symbol Marking
on the Spray Gun:
II 2 G Ex h X
This
ANEST
IWATA spray gun
complies
with
2014/34/EU
Directive relating to
equipment and
protective systems
intended for use in
explosive
potentially
atmospheres.
II
2
G
Ex h
IIB
T6
Gb
X
T
Amb
+5°C +40°C
Complies
with
European
Directive
Specific
Marking for
Explosion
Protective
Group II
(Surface)
Category
(Zone 1&2)
Type of
Atmospher
e
(GAS)
Ignition
Protection
(not applied)
Explosion
Group
(Ethylene)
Temperatur
e Class
(≤ 85°C)
Explosion
Protection
level
(EPL)
Additional
conditions:
Any static
Electricity
should be
discharged
and needs to
be diverted to
the ground via
a conductive
air hose not
included.
Ambient
Temperatu
re
Important specifications
Max. Pressure
0.70MPa / 7.0bar / 100psi
Noise level
83dB(A)
Spray condition
Recommended
Measuring point
1m backwards from spray gun, 1.6m height
Max. temperature
Atmosphere: 5°C ~40°C (41°F~104°F)
Air and Fluid: 5°C ~43°C (41°F~109°F)
Main specifications
Model
Type of
feed
Nozzle orifice
Φ mm (in)
Air cap assy
Mark
Recommended condition
Air consumption
l/min (cfm)
Pattern width
mm (in)
Air & fluid connection
Mass
g (lbs.)
*1 Atomizing air pressure
MPa (bar / PSI)
Fluid output
ml/min
WIDER1A-08E2P
Pr
ess
ur
e
0.8 (0.031)
E2P
0.29 (2.9/43)
150
270 (9.5)
190 (7.5)
【
Air
】
Atomizing air:Φ8
Operation air:Φ6
【
Fluid
】
WIDER1A:G1/4
WIDER2A:G3/8
400
(0.88)
WIDER1A-10E2P
1.0 (0.039)
200
220 (8.7)
WIDER1A-10E1
1.0 (0.039)
E1
100
90 (3.2)
140 (5.5)
WIDER1A-13H2
1.3 (0.051)
H2
250
260 (9.2)
230 (9.1)
WIDER1A-15H2
1.5 (0.059)
270
255 (10.0)
WIDER1A-05R
0.5 (0.020)
05R
20
40 (1.4)
35 (1.4)
WIDER2A-12G2P
1.2 (0.047)
G2P
500
530 (18.7)
400 (15.7)
420
(0.93)
WIDER2A-15K2
1.5 (0.059)
K2
270
330 (11.7)
340 (13.4)
WIDER2A-20R2
2.0 (0.079)
R2
400
360 (12.7)
320 (12.6)
WIDER2A-25W1
2.5 (0.098)
W1
500
360 (12.7)
330 (13.0)
*1. Atomizing air pressure means air pressure at spray gun inlet when trigger is pulled and air flows.
This manual contains IMPORTANT WARNINGS and
INSTRUCTIONS.
Equipment in this manual is exclusively for painting
purposes.
Do not use for other purposes.
The operator shall be fully conversant with the
requirements stated in this instruction manual
including important warnings, cautions and operation
and correct handling.
Read and understand the instruction manual, before
use and retain for reference.
Nozzle needle assy combination
Model
Fluid nozzle
Fluid needle
Mark
Orifice Φ
mm (in)
Mark
WIDER1A
Φ0.5
/ W1 / 05
05H WIDER1A
Φ0.8
/ W1 / 08
12H WIDER1A
Φ1.0
/ W1 / 10
Φ1.3
/ W1 / 13
15H WIDER1A
Φ1.5
/ W1 / 15
WIDER2A
Φ1.2
/ W2 / 12
12H WIDER1A
Φ1.5
/ W2 / 15
15H WIDER1A
Φ2.0
/ W2 / 20
20H WIDER2A
Φ2.5
/ W2 / 25
25H WIDER2A