1
INSTRUCTION MANUAL
HVLP Spray Gun
Be sure to observe warning s and cautions in this instruction manual.
If not, it can cause paint ejection and serious bodily injury by drawing organic solvent.
Be sure to observe following marked items which are especially important
.
Indicates a potentially hazardous situation which, if not avoided, may result in serious injury or loss of life.
Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury or
property damage.
Indicates notes which we ask you to observe. The safety precautions in this instruction manual are the
minimum necessary conditions. Follow national and local regulations regarding fire prevention,
electricity and safety as well as your own company regulations.
Symbol Marking on the Spray Gun:
II 2 G Ex h X
This ANEST IWATA spray gun
complies with 2014/34/EU Directive
relating to equipment and protective
systems intended for use in explosive
potentially atmospheres.
II
2
G
Ex h
IIB
T6
Gb
X
T
Amb
+5°C +40°C
Complies
with
European
Directive
Specific
Marking for
Explosion
Protective
Group II
(Surface)
Category
(Zone 1&2)
Type of
Atmosphere
(GAS)
Ignition
Protection
(not applied)
Explosion
Group
(Ethylene)
Temperature
Class
( 85°C)
Explosion
Protection
level
(EPL)
Additional
conditions:
Any static
Electricity
should be
discharged
and needs to
be diverted to
the ground via
a conductive
air hose not
included.
Ambient
Temperature
Important specifications
Max. Pressure
0.70MPa / 7.0bar / 100psi
Noise level
79dB(A)
Spray condition
Recommended
Measuring point
1m backwards from spray gun, 1.6m height
Max. temperature
Atmosphere: 5°C ~40°C (41°F~104°F)
Air and Fluid: 5°C ~43°C (41°F~109°F)
Important
Never connect pressure feeding paint except pressure feed type spray gun.
*1. Atomizing air pressure means air pressure at spray gun inlet when trigger is pulled and air flows.
*2. Tested with 16 s/Ford cup #4 automotive repair paint.
Nozzle needle assy combination
Model
Fluid nozzle
Fluid needle
Orifice mm (in)
Mark
Mark
WIDER1L-12G2P
1.2 (0.047)
/ W1L / 12
08H WIDER1
WIDER1L-2-12J2S/G
1.2 (0.047)
/ W1L-2 / V4-12
WIDER1L-2-14J2S/G
1.4 (0.055)
/ W1L-2 / V4-14
13 WIDER1
WIDER1L-2-16J2S/G
1.6 (0.063)
/ W1L-2 / V4-16
18 WIDER1
Main specifications
Model
Type of
feed
Fluid nozzle
Air cap assy Mark
Recommended condition
Air
consumption
l/min (cfm)
Pattern width
mm (in)
Air & fluid
connection
Mass
g (lbs.)
Nozzle orifice
mm (in)
Mark
*1 Atomizing air
pressure
MPa (bar/PSI)
Air pressure
inside air cap
MPa (bar/PSI)
Fluid output
ml/min
WIDER1L-12G2P
Pressure 1.2 (0.047)
W1L
WIDER1L-G2
0.34
(3.4 / 49.3)
0.07
(0.7 / 10)
350 530 (18.7)
270 (10.6)
Air
G1/4
(NPS1/4)
Fluid
G1/4
(NPS1/4)
290
(0.64)
WIDER1L-2-12J2S
Suction
1.2 (0.047)
W1L-2
WIDER1L-2-J2
0.10
(1.0 / 14.5)
0.05
(0.5 / 7.1)
*2
60
200 (7.1)
*2
170 (6.7)
-14J2S
1.4 (0.055)
*2
80
*2
180 (7.1)
-16J2S
1.6 (0.063)
*2
95
*2
190 (7.5)
WIDER1L-2-12J2G
Gravity
1.2 (0.047)
*2
80
*2
200 (7.9)
-14J2G
1.4 (0.055)
*2
130
*2
220 (8.7)
-16J2G
1.6 (0.063)
0.13
(1.3 / 18.9)
0.07
(0.7 / 10)
100
240 (8.5)
220 (8.7)
This manual contains IMPORTANT
WARNINGS and INSTRUCTIONS.
Equipment in this manual is exclusively for
painting purposes.
Do not use for other purposes.
The operator shall be fully conversant with
the requirements stated in this instruction
manual including important warnings,
cautions and operation and correct handling.
Read and understand the instruction
manual, before use and retain for reference.
IMPORTANT WARNING: Our spray guns, airbrushes, and other products are made to conform by our local group companies with locallaws and regulations
that may differ from place to place. Improper trade of products outside of designated domestic territories (unauthorized reselling) can result in legal violations,
local fines, and penalties. ANEST IWATA CORPORATION assumes no liability for products acquired through unauthorized reselling and in such cases and due
to quality control protocols, unauthorized reselling renders the warranty null and void.
