background image

                                                                                                   

  

3

DC HEAT RECOVERY UNIT MVHR 

INSTALLATION AND MAINTENANCE INSTRUCTIONS 

 

Read the following instructions in conjunction with the illustrations before commencing installation. 

 

1.GENERAL 

 

IMPORTANT POINTS TO NOTE 

1.  THIS APPLIANCE IS INTENDED FOR PERMANENT CONNECTION TO THE MAINS ELECTRICAL SUPPLY 

FIXED WIRING AND MUST BE INSTALLED BY A SUITABLY QUALIFIED PERSON. 

2.  THIS APPLIANCE MUST BE SITED AND CONNECTED IN ACCORDANCE WITH CURRENT UK  BUILDING, 

FACTORY AND IEE WIRING REGULATIONS (BS7671) OR THE APPROPRIATE NATIONAL REGULATIONS 
IN YOUR COUNTRY. 

3.  WIRING TO THE APPLIANCE IN THE UK MUST BE VIA A FUSED AND SWITCHED CONNECTION UNIT 

INCORPORATING A DOUBLE POLE SWITCH WITH 3mm CONTACT SEPARATION AND CONFORMING TO 
BS5733 OR BS1363 PART 4.  A 3 AMP BS1362 FUSE SHOULD BE FITTED TO THE CONNECTION UNIT, 
WHICH MUST BE LOCATED OUTSIDE OF A ROOM CONTAINING A FIXED BATH OR SHOWER. 

4.  WARNING:  THIS APPLIANCE IS CLASS I AND IT MUST THEREFORE BE EARTHED. 
5.  CHECK THE RATING LABEL ON THE APPLIANCE TO ENSURE THAT THE ELECTRICAL SUPPLY IS 

COMPATIBLE WITH THE APPLIANCE WHICH IS RATED AT 220-240V 50 Hz AC. 

6.  THIS APPLIANCE MUST BE SITED OUT OF REACH OF ANY PERSON USING A FIXED BATH OR SHOWER. 
7.  THE UNIT’S CONDENSATE DRAIN MUST BE CONNECTED TO THE BUILDING WASTE WATER DRAINAGE 

SYSTEM. 

8.  THIS APPLIANCE MUST BE SITED AWAY FROM DIRECT SOURCES OF HEAT IN EXCESS OF 40 DEGREES 

C. 

9.  UNIT MUST BE SITED IN A FROST FREE LOCATION. 
10. SITE THE APPLIANCE AND ARRANGE THE ASSOCIATED DUCTING AND GRILLES TO PROVIDE A 

BALANCED CIRCULATION OF AIR. 

11. THE EXTERNAL INTAKE TERMINALS ASSOCIATED WITH THIS APPLIANCE MUST BE SITED AT LEAST 

600mm AWAY FROM THE FLUE OF A FUEL BURNING APPLIANCE/ OTHER EXTERNAL GRILLE. 

12. ALL SAFETY REGULATIONS AND REQUIREMENTS MUST BE STRICTLY FOLLOWED TO PREVENT 

HAZARDS TO LIFE AND PROPERTY BOTH DURING AND AFTER INSTALLATION AND DURING ANY 
SUBSEQUENT MAINTENANCE AND SERVICING. 

13. SWITCH OFF THE MAINS ELECTRICAL SUPPLY BEFORE COMMENCING INSTALLATION, MAINTENANCE 

OR SERVICING. 

14. IF THE DUCTWORK PASSES THROUGH AN UNHEATED LOFT VOID OR SIMILAR LOCATION, IT MUST BE 

INSULATED. 

15. CERTAIN APPLICATIONS MAY REQUIRE THE INSTALLATION OF SOUND ATTENUATION TO ACHIEVE 

THE SOUND LEVELS REQUIRED. 

16. THIS APPLIANCE IS NOT INTENDED FOR USE BY YOUNG CHILDREN OR INFIRM PERSONS WITHOUT 

SUPERVISION. 

17. YOUNG CHILDREN SHOULD BE SUPERVISED TO ENSURE THAT THEY DO NOT PLAY WITH THE 

APPLIANCE. 

 

 
DO NOT switch off the unit except for servicing & maintenance - it is designed to run continuously. If the unit is 
switched off, indoor pollutants and moisture levels may increase and become a danger to your health and 
damage your home. 
 
It is important to follow the advice in this user manual and correctly maintain the system to ensure a healthy 
indoor environment.  

 
Disposal 
 
This product should not be disposed of with household waste. 
Please recycle where facilities exist.  Check with your local authority for recycling advice. 

 
 
 
 
 
 

Содержание 443423















Отзывы: