ANCEL FX2000 Скачать руководство пользователя страница 1

FX2000 User's Manual

i

Trademark Information

is a registered trademark of OBDSPACE TECHNOLOGY CO., LTD.

(ANCEL)in China and other countries. All other ANCEL trademarks, service

marks, domain names, logos and company names referred to in this manual are

either trademarks, registered trademarks, service marks, domain names, logos

and company names of or are otherwise the property of ANCEL or its affiliates.

In countries where any of the ANCEL trademarks, service marks, domain

names, logos and company names are not registered, ANCEL claims other

rights associated with unregistered trademarks, service marks, domain names,

logos and company names. Other products or company names referred to in

this manual may be trademarks of their respective owners. You may not use any

trademark, service mark, domain name, logo, or company name of ANCEL or

any third party without permission from the owner of the applicable trademark,

service mark, domain name, logo, or company name. You may contact ANCEL

at www.anceldirect.com, or write to OBDSPACE TECHNOLOGY CO., LTD.,

Runfeng Office, Longhua District, Shenzhen, Guangdong, 518000, P. R. China,

to request written permission to use Materials on this manual for purposes or for

all other questions relating to this manual.

Copyright Information

Copyright © 2019 by OBDSPACE TECHNOLOGY CO., LTD. All rights reserved.

No part of this publication may be reproduced, stored in a retrieval system, or

transmitted in any form or by any means, electronic, mechanical, photocopying

and recording or otherwise, without the prior written permission of ANCEL. The

information contained herein is designed only for the use of this unit. ANCEL is

not responsible for any use of this information as applied to other units.

EN

Содержание FX2000




























Отзывы: