Analytik Jena PlasmaQuant PQ 9000 Скачать руководство пользователя страница 32

Страница: 32 / 76

Installation and commissioning

Edition 05/2014

PlasmaQuant PQ 9000

Installation and commissioning

CAUTION! Prevent any unauthorized interference!

The device may only be assembled, installed and repaired by the service engineers from

Analytik Jena AG or by technical personnel authorized by Analytik Jena AG.

6.1

Supply and control connections

The supply lines are connected during the installation of the PlasmaQuant PQ 9000 by service

engineers from Analytik Jena AG.
The green power switch and the red plasma deactivation switch are located on the left-hand

side of the PlasmaQuant PQ 9000. Also on the left side, under a cover plate, there are the

connections for PC and accessories as well as the media connections for gas and the cooling

water inlet and outlet.
A pair of carrying handles are fastened to the left and right for transport and installation. The

handles are unscrewed and removed after installation. The carrying handles must be stored in a

safe place in case the device has to be transported again or moved within the laboratory.

Manual plasma

deactivation switch

Power switch

3, 4 Openings for carrying

handles

Gas connectors and

connections for water

cooling

Power cable

Fuses

Interfaces

Type plate

Figure 9

Overview of connections on the left side of the device

Содержание PlasmaQuant PQ 9000













































































Результаты поиска

Содержание PlasmaQuant PQ 9000

Отзывы:

Похожие инструкции для PlasmaQuant PQ 9000

Бренды по названию

Популярные бренды

Analytik Jena PlasmaQuant PQ 9000, Руководство по эксплуатации

Результаты поиска

Содержание PlasmaQuant PQ 9000

Отзывы:

Похожие инструкции для PlasmaQuant PQ 9000

Бренды по названию

Популярные бренды