Analog Devices SHARC ADSP-214 Series Скачать руководство пользователя | Manualshive

Страница: 702 / 1192

background image

Interrupts

18-14

ADSP-214xx SHARC Processor Hardware Reference

This sequence applies only to the first time the RTC supply (bat-
tery or I/O) is connected. Once the

RTCPDN

bit is set or reset, its

value is retained as long as RTC supply (battery or I/O) is valid.

3. After the RTC supply is connected for the first time and the

RTCPDN

bit has been cleared, the application is free to power-up and power
-down the core supply any number of times without loss of RTC
functionality (provided the RTC supply—battery or I/O, is valid).
Conversely, if the

RTCPDN

bit has been set, then the RTC oscillator

remains disabled irrespective of the status of the core supply.

4. The current status of the RTC power-down is updated by hardware

into the initialization status register (

RTC_INITSTAT

) register. This

is useful when the rest of the processor wakes up from power-down
and needs to know the status of the RTC.

5. Whenever the ADSP-2147x processor core wakes up from

power-down, the values of the

RTC_CLOCK

,

RTC_ALARM

and

RTC_SWTCH

registers is zero until the first seconds’ event after

power-up. At the first seconds’ event, an arbitrary value is uploaded
into these registers. To put them in a defined state software must
write the desired value into these registers.In case the

RTC_CLOCK

and

RTC_ALARM

have been set before core power-down and subse-

quent power-up, their values are valid throughout, but can be read
by the program only after the first seconds’ event after power-up.

Event Flags



The unknown values in the registers at power up can cause event
flags to set before the correct value is written into each of the regis-
ters. By catching the 1 Hz clock edge, the write to

RTC_CLOCK

can

occur a full second before the write to

RTC_ALARM

. This would cause

an extra second of delay between the validity of

RTC_CLOCK

and

RTC_ALARM

, if the value of the

RTC_ALARM

out of reset is the same as

www.BDTIC.com/ADI

«
...
700
701
702
703
704
...
»

Содержание SHARC ADSP-214 Series









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SHARC ADSP-214 Series

All in One Printer

Бренд: Baracoda Страницы: 42

Бренд: Queclink Страницы: 9

EK-Vector Radeon RX5700 + XT Backplate

Бренд: ekwb Страницы: 7

Бренд: SMART Страницы: 15

Easy Tool-ID BSG TID-05-T30-00-005

Бренд: Balluff Страницы: 46

memonizerWORKSTATION

Бренд: MEMON Страницы: 2

Бренд: Loopcomm Страницы: 2

Бренд: Powerleap Страницы: 28

Бренд: Advantech Страницы: 66

Бренд: ETAS Страницы: 36

Бренд: Cypress Semiconductor Страницы: 18

Бренд: Cowlacious Designs Страницы: 8

CNPS8900 Series

Бренд: ZALMAN Страницы: 10

Бренд: Intel Страницы: 57

Бренд: Hanwha Vision Страницы: 131

PMP/PTP 450 Series

Бренд: Cambium Networks Страницы: 155

Бренд: Silicon Laboratories Страницы: 91

Бренд: Johnson Controls Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды