Analog Devices SHARC ADSP-214 Series Скачать руководство пользователя | Manualshive

Страница: 640 / 1192

background image

Interrupts

15-24

ADSP-214xx SHARC Processor Hardware Reference

Full Duplex Operation

The SPI interface allows full-duplex operation running the DMA channel
to the transmit/receive path and core access to the alternate trans-
mit/receive path. For full-duplex operation, set

TIMOD

= 10 which

generates the interrupts for DMA only.

Reads from the

RXSPIx

buffer are allowed at any time during transmit

DMA. Note the

TXS

bit is cleared when the

TXSPIx

buffer is read but the

DMA FIFO is not available in the receive path. The receive interface can-
not generate an interrupt, but the

RXS

status bits can be polled.

Writes to the

TXSPIx

buffer during an active SPI receive DMA operation

are permitted. Note the

RXS

bit is cleared when the

RXSPIx

buffer is read

but the DMA FIFO is not available in the transmit path. The transmit
interface cannot generate an interrupt, but the

TXS

status bits can be

polled.

Interrupts

The following section describes SPI operations using both the core and
direct memory access (DMA).

provides an overview of SPI

interrupts.

Interrupt Sources

The SPI ports can generate interrupts in five different situations. During
core-driven transfers, an SPI interrupt is triggered:

1. When the

TXSPI

buffer has the capacity to accept another word

from the core.

2. When the

RXSPI

buffer contains a valid word to be retrieved by the

core.

www.BDTIC.com/ADI

«
...
638
639
640
641
642
...
»

Содержание SHARC ADSP-214 Series









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SHARC ADSP-214 Series

Бренд: EAW Страницы: 2

Бренд: Aastra Страницы: 2

Бренд: Lattice Semiconductor Страницы: 15

iCE40 UltraLite

Бренд: Lattice Semiconductor Страницы: 13

Бренд: SAF Страницы: 30

ST62GP-EMU2 HDS2 Series

Бренд: STMicroelectronics Страницы: 58

Бренд: UfiSpace Страницы: 35

Бренд: Point of View Страницы: 13

SABVISION NVR32

Бренд: SAB Страницы: 29

Бренд: Idis Страницы: 16

Бренд: ZIMO Страницы: 13

Бренд: OPTO 22 Страницы: 28

GEFORCE RTX 4090

Бренд: Nvidia Страницы: 160

Бренд: IFM Страницы: 12

Бренд: Alesis Страницы: 11

Бренд: NXP Semiconductors Страницы: 1202

Бренд: Xcellon Страницы: 24

Quark SoC X1000

Бренд: Galileo Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды