Analog Devices SHARC ADSP-214 Series Скачать руководство пользователя | Manualshive

Страница: 587 / 1192

background image

ADSP-214xx SHARC Processor Hardware Reference

13-17

Sony/Philips Digital Interface

detected, the

DIR_NOAUDIO

bit flag is set. If the sync code is not detected

again within 4096 frames, the

DIR_NOAUDIO

bit flag is deasserted.

The last two words of the sync code, 0xF872 and 0x4E1F, are called the
preamble-A and preamble-B of the burst preamble. Preamble-C of the
burst preamble contains burst information and is captured and stored by
the receiver. Preamble-D of the burst preamble contains the length code
and is captured by the receiver. Even if the validity bit or bit 1 of byte 0
has been set, the receiver still looks for the sync code in order to record the
preamble-C and D values. Once the sync code has not been detected in
4096 frames, the preamble-C and D registers are set to zero.



The S/PDIF receiver in 2147x and 2148x, supports all DTS frame
sizes of 256, 512, 1024, 2048 and 4096. To enable support for
2048 and 4096 DTS frame sizes, DTS_CD_4K_EN bit in
DIRCTL, need to be set. In 2146x on-chip S/PDIF receiver sup-
ports 256, 512 and 1024 DTS frames only. The DTS test kit
frames with 2048 and 4096 frame sizes can be detected by adding
the sync detection logic in software by using a software counter to
check for the DTS header every 2048 and 4096 frames
respectively.

Emphasized Audio Data

The receiver must indicate to the program whether the received audio data
is emphasized using the channel status bits as detailed below.

• In professional mode, (bit 0 of byte 0 = 1), channel status bits 2–4

of byte 0 indicate the audio data is emphasized if they are equal to
110 or 111.

• In consumer mode, (bit 0 of byte 0 = 0), channel status bits 3–5

indicate the audio data is emphasized if they are equal to 100, 010
or 110.

If emphasis is indicated in the channel status bits, the receiver asserts the

EMPHASIS

bit flag. This bit flag is used to generate an interrupt.

www.BDTIC.com/ADI

«
...
585
586
587
588
589
...
»

Содержание SHARC ADSP-214 Series









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SHARC ADSP-214 Series

Бренд: IBM Страницы: 86

Бренд: GE Страницы: 146

8677 - BladeCenter Rack-mountable - Power...

Бренд: IBM Страницы: 126

Бренд: BSS Audio Страницы: 20

Бренд: Reeven Страницы: 2

Бренд: Roland Страницы: 12

Бренд: vPipes Страницы: 3

Бренд: hilscher Страницы: 154

RCO-3000 Series

Бренд: C&T Solution Страницы: 96

Бренд: Grundig Страницы: 24

Бренд: Z3 Technology Страницы: 67

Бренд: CNC4PC Страницы: 11

Бренд: C-Smartlink Страницы: 7

Бренд: Idis Страницы: 20

UniFi LED ULED-AT

Бренд: Ubiquiti Страницы: 16

Бренд: Nortel Страницы: 163

Бренд: Baracoda Страницы: 16

Бренд: Icy Box Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды