Analog Devices SHARC ADSP-214 Series Скачать руководство пользователя | Manualshive

Страница: 545 / 1192

background image

ADSP-214xx SHARC Processor Hardware Reference

11-25

Input Data Port

Debug Features

The following sections describe the features available for debugging the
IDP.

Status register Debug

The core may also write to the FIFO. When it does, the audio data word is
pushed into the input side of the FIFO (as if it had come from the SRU
on the channel encoded in the three LSBs). This can be useful for verify-
ing the operation of the FIFO, the DMA channels, and the status portions
of the IDP. The

IDP_STAT1

register returns the current state of the

read/write index pointers from FIFO.

Buffer Hang Disable

The

IDP_BHD

bit in

IDP_CTL0

is used for buffer hang disable control. When

there is no data in the FIFO, reading the

IDP_FIFO

register causes the core

to hang. This condition continues until the FIFO contains valid data. Set-
ting the

IDP_BHD

bit (= 1) prevents the core from hanging on reads from

an empty

IDP_FIFO

register. Clearing this bit (= 0) causes the core to hang

under the conditions described previously.

If the

IDP_BHD

bit (bit 4 in the

IDP_CTL0

register) is not set, attempts to

read more data than is available in the FIFO results in a core hang.

Shadow Registers

The DAI interrupt controller contains shadow registers to simplify debug
techniques since these register are not updated. A read of the

DAI_IMASK_x_SH

register provides the same data as a read of the

DAI_IMASK_x

register. Reading these DAI shadow registers

(

DAI_IMASK_x_SH

) does not destroy the contents of the

DAI_IMASK_x

registers.

www.BDTIC.com/ADI

«
...
543
544
545
546
547
...
»

Содержание SHARC ADSP-214 Series









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SHARC ADSP-214 Series

Бренд: Qualys Страницы: 2

Scorpio WD2500BPVT

Бренд: Western Digital Страницы: 3

Scorpio WD2500BPVT

Бренд: Western Digital Страницы: 4

Бренд: Wintech Страницы: 21

Бренд: Parker Страницы: 50

Бренд: Crystal Vision Страницы: 54

Бренд: Loopcomm Страницы: 2

Бренд: PADAUK Страницы: 27

Бренд: sound4 Страницы: 66

WAFER-EHL Series

Бренд: IEI Technology Страницы: 142

Бренд: RadioSPECTRAL Страницы: 2

Бренд: ZALMAN Страницы: 9

Бренд: ICP DAS USA Страницы: 62

Бренд: ICP DAS USA Страницы: 8

Matrix 6H303-48

Бренд: Enterasys Страницы: 90

CNPS7000B Series

Бренд: ZALMAN Страницы: 9

Бренд: C-Data Страницы: 19

Бренд: ICS Advent Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды