Analog Devices SHARC ADSP-214 Series Скачать руководство пользователя | Manualshive

Страница: 544 / 1192

background image

Interrupts

11-24

ADSP-214xx SHARC Processor Hardware Reference

DMA Interrupts

Using DMA transfer overrides the mechanism used for interrupt-driven
core reads from the FIFO. When the

IDP_DMA_EN

bit and at least one

IDP_DMA_ENx

of the

IDP_CTL1

register are set, the eighth interrupt

(

IDP_FIFO_GTN_INT

) in the

DAI_IMASK_x

registers is NOT generated.

At the end of the DMA transfer for individual channels, interrupts are
generated. These interrupts are generated after the last DMA data from a
particular channel has been transferred to memory. These interrupts
(

IDP_DMAx_INT

) are mapped from the bits 17–10 in the

DAI_IMASK_x

registers and generate interrupts when they are set (= 1). These bits are
ORed and reflected in high level interrupts that are sent to the DAI
interrupt.

An interrupt is generated at the end of a DMA, which is cleared by read-
ing the

DAI_IMASK_x

registers.

FIFO Overflow Interrupts

If the data out of the FIFO (either through DMA or core reads) is not suf-
ficient to transfer at the combined data rate of all the channels, then a
FIFO overflow can occur. When this happens, new data is not accepted.
Additionally, data coming from the serial input channels (except for
32-bit I

2

S and left-justified modes) are not accepted in pairs, so that alter-

nate data from a channel is always from left and right channels. If overflow
occurs, an interrupt is generated if the

IDP_FIFO_OVR_INT

bit in the

DAI_IMASK_x

register is set (sticky bits in

DAI_STAT0

register are also set).

Data is accepted again when space has been created in the FIFO.

Note that the total FIFO depth per channel is 9 locations: 1 location for
SIP to parallel data conv 8 locations for the

IDP_FIFO

.

www.BDTIC.com/ADI

«
...
542
543
544
545
546
...
»

Содержание SHARC ADSP-214 Series









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SHARC ADSP-214 Series

Бренд: D-Link Страницы: 15

Бренд: C4i Страницы: 8

Бренд: Ebyte Страницы: 14

Бренд: IBA Страницы: 29

Бренд: Cypress Semiconductor Страницы: 9

CLICK PLUS C2-02CPU

Бренд: Automationdirect.com Страницы: 10

Бренд: MiLAN Страницы: 1

PacketShaper PS-S200

Бренд: Symantec Страницы: 2

Бренд: Roland Страницы: 12

eBOX532-100-FL Series

Бренд: AXIOMTEK Страницы: 2

Бренд: FONESTAR Страницы: 8

Бренд: iCEBOX Страницы: 57

J-Link-OB-STM32F072-128KB

Бренд: Segger Страницы: 18

CHEETAH ST34501FC

Бренд: Seagate Страницы: 68

Бренд: ADS Technologies Страницы: 1

Бренд: CSL Страницы: 24

Бренд: AMC Страницы: 28

Бренд: Cypress Semiconductor Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды