Analog Devices SHARC ADSP-214 Series Скачать руководство пользователя | Manualshive

Страница: 501 / 1192

background image

ADSP-214xx SHARC Processor Hardware Reference

10-43

Serial Ports



When 16-bit received data is packed into 32-bit words and stored
in normal word space in processor internal memory, the 16-bit
words can be read or written with short word space addresses

Core Transfers

The following sections provide information on core driven data transfers.

Single Word Transfers

Individual data words may also be transmitted and received by the serial
ports, with interrupts occurring as each 32-bit word is transmitted or
received. When a serial port is enabled and DMA is disabled, the SPORT
interrupts are generated whenever a complete 32-bit word has been
received in the receive buffer, or whenever the transmit buffer is not full.

When performing core-driven transfers, write to the buffer designated by
the

SPTRAN

bit setting in the

SPCTLx

register. For DMA-driven transfers,

the serial port logic performs the data transfer from internal memory
to/from the appropriate buffer depending on the

SPTRAN

bit setting. If the

inactive SPORT data buffers are read or written to by core while the port
is being enabled, the core hangs. For example, if a SPORT is programmed
to be a transmitter, while at the same time the core reads from the receive
buffer of the same SPORT, the core hangs just as it would if it were
reading an empty buffer that is currently active. This locks up the core
until the SPORT is reset.

To avoid hanging the processor core, check the buffer’s full/empty status
when the processor core’s program reads a word from a serial port’s receive
buffer or writes a word to its transmit buffer. This condition can also hap-
pen to an external device, for example a host processor, when it is reading
or writing a serial port buffer. The full/empty status can be read in the

DXS

bits of the

SPCTLx

register. Reading from an empty receive buffer or writ-

ing to a full transmit buffer causes the processor (or external device) to
hang, while it waits for the status to change.

www.BDTIC.com/ADI

«
...
499
500
501
502
503
...
»

Содержание SHARC ADSP-214 Series









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SHARC ADSP-214 Series

Бренд: 3Com Страницы: 20

Бренд: Garland Страницы: 4

Бренд: Q-See Страницы: 2

Бренд: Alesis Страницы: 61

Бренд: Kaptia Страницы: 14

Бренд: EMTRUST Страницы: 103

Бренд: Network Critical Страницы: 200

Бренд: Xyclop Страницы: 144

Бренд: Silvertel Страницы: 9

Бренд: National Instruments Страницы: 121

Q-SYS QIO-GP8x8

Бренд: QSC Страницы: 13

Бренд: RAK Страницы: 14

Бренд: ICP DAS USA Страницы: 8

Linktropy MINI-G

Бренд: Apposite Technologies Страницы: 57

Бренд: Corsair Страницы: 134

Бренд: AG Страницы: 10

S5U13719P00C100

Бренд: Epson Страницы: 31

Бренд: Epson Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды