Analog Devices SHARC ADSP-214 Series Скачать руководство пользователя | Manualshive

Страница: 1034 / 1192

background image

Peripherals Routed Through the DAI

A-208

ADSP-214xx SHARC Processor Hardware Reference

4 (ROC)

DIR_LOCK

Lock Receiver.

When set (=1), the digital PLL of receiver is

locked, the corresponding DIR_LOCK bit is set. This bit
can be polled to detect the DIR_LOCK condition. After
the receiver is locked, the other status bits in DIRSTAT
and the channel status (DIRCHANL/R) registers can be
read. Interrupts can be also used with some status bits.
0 = Receiver not locked
1 = Receiver locked

5 (ROC)

DIR_NOSTREAM

No Stream Error.

Asserted when the AES3/SPDIF stream

is disconnected. When this bit is asserted and the audio
data in the stream is linear PCM, the receiver performs a
soft mute of the last valid sample from the AES3/SPDIF
stream. A soft mute consists of taking the last valid audio
sample and slowly and linearly decrementing it to zero,
over a period of 4096 frames. During this time, the PLL
three-states the charge pump until the soft mute has been
completed. If non-linear PCM audio data is in the
AES3/SPDIF stream when the NOSTREAM bit is
asserted, the receiver sends out zeros after the last valid
sample.
0 = Stream not disconnected
1 = Stream disconnected (default)

6 (ROC)

DIR_PARITYERROR

Parity Bit.

When cleared, (=0), indicates that the

AES3/SPDIF stream was received with the correct parity,
or even parity. When set (=1), indicates that an error has
occurred, and the parity is odd.
0 = No parity error
1 = Parity error

7 (ROC)

DIR_BIPHASEERROR

Biphase Error.

When set (=1), indicates that a bi-phase

error has occurred and the data sampled from the biphase
stream may not be correct.
0 = No biphase error
1 = Biphase error

15–8

Reserved

23–16

DIR_B0CHANL

Channel Status Byte 0 for Subframe A.

31–24

DIR_B0CHANR

Channel Status Byte 0 for Subframe B.

Table A-110. DIRSTAT Register Bit Descriptions (RO) (Cont’d)

Bit

Name

Description

www.BDTIC.com/ADI

«
...
1032
1033
1034
1035
1036
...
»

Содержание SHARC ADSP-214 Series









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SHARC ADSP-214 Series

COMSPHERE 3800 Series

Бренд: Paradyne Страницы: 88

COMSPHERE 3800PLUS

Бренд: Paradyne Страницы: 5

Бренд: Uniden Страницы: 5

Бренд: Advantech Страницы: 68

640 - Pentium 4 640 3.2GHz 800MHz 2MB Socket 775 CPU

Бренд: Intel Страницы: 105

Бренд: MSNswitch Страницы: 2

Бренд: Hama Страницы: 25

IP-Logic ZIG-IPPRO-RX

Бренд: Zigen Страницы: 4

Бренд: Lattice Semiconductor Страницы: 43

ACCULINK 3161 CSU

Бренд: Paradyne Страницы: 19

Бренд: Supermicro Страницы: 131

Бренд: Alcatel-Lucent Страницы: 12

Бренд: Altera Страницы: 40

Бренд: Milesight Страницы: 15

Бренд: Watchguard Страницы: 21

Бренд: HYCON Страницы: 13

Бренд: Intel Страницы: 11

Бренд: ProCurve Страницы: 406

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды