manualshive.com logo in svg

Analog Devices ADuCM310, Справочник по аппаратуре

Поделиться
Скачать
Analog Devices ADuCM310 Скачать руководство пользователя страница 79

ADuCM310 Hardware Reference Manual 

UG-549 

 

Rev. C | Page 79 of 192 

FLASH CONTROLLER 

FLASH CONTROLLER FEATURES 

The flash controller features are as follows: 

•

 

256 kB Flash/EE memory in 2 blocks of 128 kB each (Flash 0 and Flash 1) 

•

 

4 kB information space, which contains factory code 

FLASH CONTROLLER OVERVIEW 

The flash controller supports read on one flash block and erase/write operation on the other block. There is peripheral DMA support for 
flash keyhole-based write. A kernel is present in the information space. 
The flash controller supports buffered read, that is, executing code from a 64-bit read while fetching next 64 bits.  
The flash controller is a 32-bit interface for MMR access. Flash program and erase timing are controlled via a fixed 16 MHz reference clock.  
The keyhole is open for access, command fail, and command complete status bits. A cache is provided to speed up execution.  

Commands 

The flash controller supports the following commands: 

•

 

Write command: 64-bits per write 

•

 

Page erase commands 

•

 

Mass erase commands for each flash block 

•

 

Generation of signatures for single or multiple pages 

•

 

Command abort supported (by writing to command MMR or by system interrupt) 

•

 

Keys required for running commands such as mass erase and the test commands 

Protection, Integrity 

The flash controller supports the following protection and integrity features: 

•

 

Write/read protection for user space 

•

 

Read and write protection for information space 

•

 

Ability to lock the SW/JTAG interface 

•

 

Automatic signature check of information space on reset 

•

 

User signature check of user space and information space 

•

 

8-bit ECC 

•

 

1-bit ECC error correction 

•

 

1-bit ECC errors and 2-bit or greater ECC errors can be configured to generate a flash ECC interrupt or a system exception 

Содержание ADuCM310

































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды