Analog Devices ADSP-2181 Скачать руководство пользователя | Manualshive

Страница: 56 / 70

background image

Designing EZ-ICE Compatible Systems

3-14

ADSP-2181 EZ-KIT Lite Evaluation System Manual

should be 8V to 10V DC. Also, make sure that there are no objects
beneath or on top of the board that may be causing a short circuit. Hit the
reset button (

S1

) if the board appears to be operating improperly.

Designing EZ-ICE Compatible Systems

This section describes the ADSP-218x family EZ-ICE theory of operation
to aid your EZ-ICE compatible system designs.

The hardware consists of a printed circuit board measuring 3.5 inches by
5.5 inches. Assembled onto the printed circuit board are: an ADSP-2181
digital signal processor, a socketed EPROM, an AD1847 codec, and vari-
ous support circuits and connectors. The board is a complete signal
processing system designed to demonstrate the capabilities of the
ADSP-2181 digital signal processor. It can also be used as a platform to
develop new applications targeting ADSP-2181 processors.

The EZ-KIT Lite board is an example of a minimum implementation of
an ADSP-2181 processor. The socketed EPROM is connected to the pro-
cessor via the Byte DMA Port. This interface uses only eight of the
twenty-four data lines to carry data (

D8

through

D15

). Eight of the spare

data lines (

D16

through

D23

) are used to provide additional address bits.

This allows the ADSP-2181 to address up to 32 Mbits (4 Mbytes) of
memory. The DSP is configured to boot from the socketed EPROM when

RESET

is de-asserted or if power is applied to the board.

The AD1847 codec is connected to the DSP via

SPORT0

. This high speed

synchronous serial port carries all of the data, control, and status informa-
tion between the DSP and the codec. It is possible to disable the codec if
the serial port is to be used for another purpose. The

CODECDIS

signal

available on connector

P3

can be used to disable the codec. When this sig-

nal is brought low, the codec is disabled and its signals are put in a high
impedance state.

«
...
54
55
56
57
58
...
»

Содержание ADSP-2181







































































Отзывы:

Нет отзывов

Похожие инструкции для ADSP-2181

Бренд: Jabra Страницы: 15

WS-650 lite Series

Бренд: Laurell Страницы: 84

Transportation FiberinMotion

Бренд: Radwin Страницы: 122

Бренд: A10 Страницы: 52

Бренд: Opvimus Страницы: 12

APS6-400 Series

Бренд: Eaton Страницы: 114

Бренд: T.A Страницы: 11

Wisenet PRN-6400B4

Бренд: Hanwha Techwin Страницы: 14

Бренд: ZALMAN Страницы: 9

Converter Board R0E5212BACFG00

Бренд: Renesas Страницы: 6

Бренд: Cypress Semiconductor Страницы: 16

EZ-Extender Analog 120-Pin Probing Board

Бренд: Analog Devices Страницы: 29

Seven Solutions WR-ZEN Series

Бренд: Orolia Страницы: 167

Бренд: Comelit Страницы: 19

OMB-DAQBOARD-500 Series

Бренд: Omega Страницы: 48

Бренд: ZALMAN Страницы: 16

MTDOT-868 Series

Бренд: Multitech Страницы: 60

STEVAL-SCR002V1

Бренд: ST Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды