Analog Devices ADSP-21261 SHARC Скачать руководство пользователя страница 610 | Manualshive

Страница: 610 / 846

background image

Booting

15-20

ADSP-2126x SHARC Processor Hardware Reference

The ADSP-2126x supports three booting modes—EPROM, SPI master
and SPI slave. Each of these modes uses the following general procedure:

1. At reset, the ADSP-2126x is hardwired to load two hundred

fifty-six 32-bit instruction words via a DMA starting at location
0x80000. In this chapter, these instructions are referred to as the

boot kernel

or

loader kernel.

2. The DMA completes and the interrupt associated with the periph-

eral that the processor is booting from is activated. The processor
jumps to the applicable interrupt vector location (0x80030 for SPI
and 0x80050 for the parallel port) and executes the code located
there. (Typically, the first instruction at the interrupt vector is a
Return From Interrupt (RTI) instruction.)

3. The loader kernel executes a series of Direct Memory Accesses

(DMAs) to import the rest of the application, overwriting itself
with the applications’ Interrupt Vector Table (IVT).

4. After executing the kernel, the processor returns to location

0x80005 where normal program execution begins.

To support this process, a 256-word loader kernel and loader (which con-
verts executables into boot-loader images) are supplied with the CrossCore
or Vi+ development tools for both SPI and parallel port booting.
For more information on the loader, see the tools documentation.

The boot source is determined by strapping the two

BOOTCFGx

pins to

either logic low or logic high. These settings are shown in

.

«
...
608
609
610
611
612
...
»

Содержание ADSP-21261 SHARC















































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ADSP-21261 SHARC

Бренд: B2 Страницы: 52

COMSPHERE 3800 Series

Бренд: Paradyne Страницы: 88

COMSPHERE 3800PLUS

Бренд: Paradyne Страницы: 5

Бренд: TC Electronic Страницы: 55

Бренд: Paradyne Страницы: 1

JetWeb JX2-PR0FI1

Бренд: Jetter Страницы: 67

Magic WiFi mini Ek

Бренд: Devolo Страницы: 22

Бренд: Ubiquiti Страницы: 13

VIGI NVR1004H-4P

Бренд: TP-Link Страницы: 2

Бренд: IEI Technology Страницы: 2

Бренд: Xantech Страницы: 5

Бренд: ICS ELECTRONICS Страницы: 4

Бренд: Altimium Страницы: 12

Бренд: Digisol Страницы: 73

FiberTwist XGS2420

Бренд: Genexis Страницы: 7

Бренд: H3C Страницы: 62

Бренд: Paradyne Страницы: 46

Бренд: Vertilon Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды