Analog Devices ADSP-21261 SHARC Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 846

background image

Architectural Overview

1-12

ADSP-2126x SHARC Processor Hardware Reference

transmit modes. Serial port clocks and frame syncs can be internally or
externally generated.

Parallel Port.

The ADSP-2126x parallel port provides the processor inter-

face to asynchronous 8-bit memory. The parallel port supports a 66M
bytes per second transfer rate and 256 word page boundaries. The on-chip
DMA controller automatically packs external data into the appropriate
word width during transfers.

The parallel port supports packing of 32-bit words into 8-bit or 16-bit
external memory and programmable external data access duration from 3
to 32 clock cycles.

Serial Peripheral (Compatible) Interface (SPI).

The ADSP-2126x SPI is

an industry standard synchronous serial link that enables the SPI-compat-
ible port to communicate with other SPI-compatible devices. SPI is an
interface consisting of two data pins, one device select pin, and one clock
pin. It is a full-duplex synchronous serial interface, supporting both mas-
ter and slave modes. It can operate in a multi master environment by
interfacing with up to four other SPI-compatible devices, either acting as a
master or slave device.

The SPI-compatible peripheral implementation also supports programma-
ble baud rate and clock phase/polarities, as well as the use of open drain
drivers to support the multi master scenario to avoid data contention.

ROM Based Security.

For ADSP-2126x processors with application code

in the on-chip ROM, an optional ROM security feature is included. This
feature provides hardware support for securing user software code by pre-
venting unauthorized reading from the enabled code. The processor does
not boot-load any external code, executing exclusively from internal
ROM. The processor also is not freely accessible via the JTAG port.
Instead, a 64-bit key is assigned to the user. This key must be scanned in
through the JTAG or Test Access Port. The device ignores a wrong key.
Emulation features and external boot modes are only available after the
correct key is scanned.

«
...
50
51
52
53
54
...
»

Содержание ADSP-21261 SHARC















































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ADSP-21261 SHARC

Бренд: TC-Helicon Страницы: 2

OMB-DAQBOARD-3000 Series

Бренд: Omega Страницы: 108

Бренд: Altera Страницы: 93

NetVanta 6355 PoE

Бренд: ADTRAN Страницы: 46

Momentum ROG Strix X570-E D-RGB

Бренд: EK-Quantum Страницы: 10

Бренд: MSNswitch Страницы: 2

Open Standard Module RPX30 EVA-MI V1

Бренд: iesy Страницы: 9

Бренд: RME Audio Страницы: 7

Бренд: IBASE Technology Страницы: 49

Бренд: XMOS Страницы: 8

Бренд: Rosewill Страницы: 5

Бренд: Cypress Semiconductor Страницы: 31

Бренд: MSI Страницы: 3

Бренд: ELC Страницы: 12

Бренд: StarTech.com Страницы: 8

Бренд: NEC Страницы: 6

NEC Express5800 Series

Бренд: NEC Страницы: 2

Бренд: NEC Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды