Analog Devices ADDS-21992-EZLITE Скачать руководство пользователя страница 50

Страница: 50 / 62

ADSP-21992 EZ-KIT Lite Evaluation System Manual

4-45

4.4.11 USB Connector, P11

The USB connector is a standard type B USB receptacle.

Part Description

Manufacturer

Part Number

Mill-Max

897-30-004-90-000

Type B USB receptacle

Digi-Key

ED90003-ND

Mating Connector

Assmann

AK672-5

USB cable (provided with kit)

Digi-Key

AK672-5ND

4.4.12 CAN Interface Connector, P12–P13

There are two connectors associated with the CAN interface circuitry on the ADSP-21992 EZ-
KIT Lite board. Connectors P12 and P13 provide connections to the user’s CAN bus and allow
easy daisy-chaining of CAN devices.

PIN

NAME

SIGNAL

DGND

Digital Ground

CANL

CAN Receive

CANH

CAN Transmit

+3.3V

Vddext

Table 4-11: CAN Interface Connectors, P12 and P13

4.4.13 JTAG Connector

The JTAG header is the connecting point for a JTAG in-circuit emulator pod.

Note

: Pin 3 is missing to provide keying. Pin 3 in the mating connector should have a plug.

When an emulator is connected to the JTAG header, the USB debug interface is disabled.

WARNING: When using an emulator with the EZ-KIT Lite board, follow the
connection instructions provided with the emulator.

4.5 Mechanical

Dimensions

Figure 4-6

shows the dimensions of the board.

Содержание ADDS-21992-EZLITE































































Результаты поиска

Содержание ADDS-21992-EZLITE

Отзывы:

Похожие инструкции для ADDS-21992-EZLITE

Бренды по названию

Популярные бренды

Analog Devices ADDS-21992-EZLITE, Руководство пользователя

Результаты поиска

Содержание ADDS-21992-EZLITE

Отзывы:

Похожие инструкции для ADDS-21992-EZLITE

Бренды по названию

Популярные бренды