Analog Devices AD9516 страница 16 Скачать руководство пользователя | Manualshive

Страница: 16 / 16

background image

UG-075

Evaluation Board User Guide

Rev. 0 | Page 16 of 16

NOTES

ESD CAUTION

Evaluation boards are only intended for device evaluation and not for production purposes. Evaluation boards are supplied “as is” and without warranties of any kind, express,
implied, or statutory including, but not limited to, any implied warranty of merchantability or fitness for a particular purpose. No license is granted by implication or otherwise under
any patents or other intellectual property by application or use of evaluation boards. Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Analog Devices reserves the
right to change devices or specifications at any time without notice. Trademarks and registered trademarks are the property of their respective owners. Evaluation boards are not
authorized to be used in life support devices or systems.

©2010 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.

UG08745-0-1/10(0)

www.BDTIC.com/ADI

«
...
14
15
16

Содержание AD9516

















Отзывы:

Нет отзывов

Похожие инструкции для AD9516

Бренд: Lantronix Страницы: 8

phyBOARD-Subra-i.MX6

Бренд: Phytec Страницы: 2

Бренд: FAAC Страницы: 8

Бренд: Texas Instruments Страницы: 38

CLICKER 4 for STM32

Бренд: Mikroe Страницы: 16

Бренд: Supermicro Страницы: 142

XILINX SPARTAN-7

Бренд: QMTECH Страницы: 15

Spartan-7 SP701

Бренд: Xilinx Страницы: 4

Qseven conga-QA5

Бренд: Congatec Страницы: 61

Бренд: IEI Technology Страницы: 194

Бренд: BCM Страницы: 3

Бренд: Intel Страницы: 112

Бренд: MSI Страницы: 6

CT-PBT01 Series

Бренд: C&T Solution Страницы: 48

Бренд: MSI Страницы: 148

Бренд: TYAN Страницы: 117

Бренд: Supero Страницы: 108

LanParty LT P35

Бренд: DFI Страницы: 167

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды