Analog Devices AD5934 Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 40

Analog Devices AD5934 Скачать руководство пользователя страница 34

AD5934

Rev. A | Page 34 of 40

EVALUATION BOARD

The AD5934 evaluation board allows designers to evaluate
the high performance AD5934 impedance converter with
minimum effort.

The evaluation board interfaces to the USB port of a PC. It is
possible to power the entire board from the USB port.

The impedance converter evaluation kit includes a populated
and tested AD5934 printed circuit board. The EVAL-AD5934EBZ
kit is shipped with a CD-ROM that includes self-installing
software. Connect the PC to the evaluation board using the
supplied cable.

The software is compatible with Microsoft® Windows® 2000 and
Windows XP.

A schematic of the evaluation board is shown in Figure 40 and
Figure 41.

USING THE AD5934 EVALUATION BOARD

The evaluation board is a test system designed to simplify the
evaluation of the AD5934. The evaluation board data sheet that
is available with the evaluation board gives full information on
how to operate the evaluation board. Further evaluation
information is available from

PROTOTYPING AREA

An area is available on the evaluation board for the user to add
additional circuits to the evaluation test set. Users may want to
include switches for multiple calibration use.

CRYSTAL OSCILLATOR (XO) vs. EXTERNAL CLOCK

A 16 MHz oscillator is included on the evaluation board.
However, this oscillator can be removed and, if required, an
external CMOS clock can be connected to the part.

«
...
32
33
34
35
36
...
»

Содержание AD5934









































Отзывы:

Нет отзывов