Analog Devices AD5934 Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 40

Analog Devices AD5934 Скачать руководство пользователя страница 3

AD5934

Rev. A | Page 3 of 40

REVISION HISTORY

5/8—Rev. 0 to Rev. A

Changes to Layout.............................................................. Universal
Changes to Features Section, General Description Section, and
Figure 1 ...............................................................................................1
Deleted Table 1; Renumbered Sequentially ...................................1
Changes to Table 1 ............................................................................4
Changes to Table 2 ............................................................................6
Changes to Figure 3 and Table 4 .....................................................8
Changes to System Description Section and Figure 14..............12
Changes to Figure 16 ......................................................................13
Changes to Frequency Sweep Command Sequence Section and
Receive Stage Section......................................................................14
Changes to Gain Factor Calculation Section and Impedance
Calculation Using Gain Factor Section ........................................15
Changes to Figure 20 ......................................................................16
Changes to Impedance Error Section...........................................17
Added Measuring the Phase Across an Impedance Section .....19
Added Figure 28 and Figure 29; Renumbered Sequentially ......20

Added Table 6; Renumbered Sequentially...................................20
Deleted Table 8 ................................................................................19
Deleted Table 10 and Table 11 .......................................................20
Changes to Table 9 ..........................................................................22
Deleted Table 14, Table 16, and Table 17 .....................................22
Changes to Status Register (Register Address 0x8F) Section....24
Added Measuring Small Impedances Section, Figure 37, and
Table 16.............................................................................................29
Changes to Table 17 ........................................................................32
Added Evaluation Board Section ..................................................34
Added Figure 40 ..............................................................................35
Added Figure 41 ..............................................................................36
Added Figure 42 ..............................................................................37
Added Figure 43 ..............................................................................38
Added Table 18 ................................................................................39
Changes to Ordering Guide...........................................................40

6/05—Revision 0: Initial Version

«
1
2
3
4
5
...
»

Содержание AD5934









































Отзывы:

Нет отзывов