background image

Safety Instructions

c

PLB-AMP8 8-Channel Audio Power Amplifier

19.

Object and Liquid Entr

y - Never push objects of any kind into this product through openings, 

as they may contact dangerous voltage points or short out parts, resulting in a fire or electrical 

shock. Never spill any kind of liquid on this product.

20.

Servicing

 - Do not attempt to service this product yourself, as opening or removing covers 

may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service 

personnel.

21.

Damage Requiring Service

 - Unplug this product from the wall outlet or other power source. 

Refer servicing to qualified service personnel under the following conditions:

a.  

When the power supply cord or plug is damaged.

b.  

If liquid has been spilled on the product or if objects have fallen into the product.

c.  

If the product has been exposed to rain or water.

d.  

If the product does not operate normally by following the operating instructions, adjust 

only those controls that are covered by the operating instructions. An improper adjustment 

of other controls may result in damage and will often require extensive work by a qualified 

technician to restore the product to its normal operation.

e.  

If the product has been dropped or damaged in any way.

f.  

When the product exhibits a distinct change in performance. This indicates a need for 

service.

22.

Replacement Parts

 - When replacement parts are required, make sure the service technician 

has used replacement parts that are specified by the manufacturer or have the same 

characteristics as the original parts. Unauthorized substitutions may result in fire, electrical 

shock, or other hazard.

23.

Safety Check

 - Upon completion of any service or repairs to this product, ask the service 

technician to perform safety checks to determine that the product is in proper operating 

condition.

24.

Wall or Ceiling Mounting

 - The product should be mounted to a wall or ceiling only as 

recommended by the manufacturer.

FIG. 1  

Outdoor antenna grounding

Содержание PLB-AMP8

















Отзывы: