Quick Start Guide
MB-TP17
Universal VESA Mounting Box for 17" Modero Panels
The MB-TP17 Universal VESA™ Mounting Kit (
FG033-50
) allows the 17"
Modero touch panels to be mounted on a pivot/pitch, extendable arm, pole,
ceiling, under-cabinet mount, or any other variation of VESA-compliant mounting
hardware.
The MB-TP17 kit includes everything the installer needs to mount a 17” Modero
panel (wall mount version) to any standard 75mm x 75mm VESA mounting
hardware (purchased separately). The kit includes a metal back box, a plastic
rear cover (with cable routing hole (which accepts the included strain-relief
grommet) and other required hardware (see Specifications table for details). .
Specifications
Overview - Installing the MB-TP17 Kit
Upgrading the original Modero back box with the MB-TP17 Universal VESA
Mounting Kit involves three main processes:
•
Removing the original Modero back box, and installing the new
MB-TP17 back box.
•
Threading cables through the strain relief grommet opening in the rear
plastic cover.
•
Finalizing the installation of the NXD (with MB-TP17 back box and
cables) into the plastic cover, securing both components, and finalizing
the strain relief grommet installation.
Removing the Original Modero Back Box
1.
Detach all connectors from the side of the touch panel.
2.
Remove the magnetic faceplate from the NXD unit by carefully
gripping the faceplate and pulling outwards.
3.
Place the LCD face-down on a soft cloth to expose the back of the
panel and prevent scratching of the LCD.
4.
Unscrew the headphone nut from the headphone jack.
5.
Remove the metal connector overlay by using a grounded Phillips-
head screwdriver to turn the two screws and slide the metal
connector overlay away from the back box housing.
6.
Remove the four pan-head housing screws from the rear of the NXD
unit (FIG. 2). These screws secure the back box to the internal panel
casing.
7.
Lift the back box housing to separate it from the internal panel casing.
Note
:
Do not remove the four panel securing screws.
These screws secure the
LCD to the metal casing.
Installing the MP-TP17 Back Box
1.
Unscrew the four pan-head Housing screws (#8-32) from the
MB-TP17 rear plastic cover.
2.
Gently place the MB-TP17 back box over the internal panel casing
(with the cable routing hole on the right-side of the panel).
3.
Re-install and secure the four pan-head Housing screws into their
pre-drilled holes along the edges of the MB-TP17 back box (FIG. 2)
and secure them using a grounded Phillips-head screwdriver.
4.
Replace the Connector Overlay back over the connector opening and
align the connector locations.
5.
Re-secure the metal connector overlay (using a grounded Phillips-
head screwdriver) and re-secure the nut on the headphone jack.
Cable Installation for the MP-TP17 Back Box
1.
Connect the cable connectors (RJ-45, Ethernet, and any other
audio/video wiring) to their respective locations along the side of the
touch panel.
2.
Use the tie-wrap (45-0009A) to wrap the cables together inside the
VESA Mount enclosure. This cable tie is used to insure the cable will
not pull through or work itself through the new larger strain relief
grommet (45-0032-01) over time.
3.
Thread the incoming cables through the hole on the rear plastic cover
and then through the strain relief grommet.
4.
Slide the grommet along the cable and securely insert it into the
opening on the rear plastic cover (FIG. 4).
Finalizing the Installation
1.
Gently place the rear plastic cover over the NXD panel (with LCD and
MB-TP17 back box).
2.
Insert the protruding cables, coming out from the opening on the rear
plastic cover, into the open strain relief grommet.
3.
Allow some slack/length on these cables as a service loop. This ser-
vice loop provides enough cable length so you can later remove the
NXD (with connected cables) from the rear plastic cover.
FIG. 1
MB-TP17 Universal VESA Mounting Box and Rear Cover (rear view)
MB-TP17 Specifications
MB-TP17 Mounting Kit -
Installed Dimensions
(HWD):
• 14.44" x 18.09" x 3.48" (36.68 cm x 45.95 cm x 8.84 cm)
Operating /Storage
Environments:
• Operating Temperature: 0° C (32° F) to 40° C (104° F)
• Operating Humidity: 20% - 85% RH
• Storage Temperature: -20° C (-4° F) to 60° C (140° F)
• Storage Humidity: 5% - 85% RH
Included Accessories
• Black metallic VESA back box (62-0033-50)
• Black plastic cover (with grommet opening) (60-0033-50)
• Four Phillips pan-head screws (#8-32 x 0.50 Black)
(80-0146-02)
• Tie Wrap (
Large
) (45-0009A) (
for use with NXA-MTC/RGB
)
• Ten Under-cut Phillips-head screws (#6-32 x 0.500 Black)
(80-0139)
• Strain relief grommet (45-0004-03) (
for use with CA2250-50
)
• Universal VESA Msount grommet (45-0032-01)
(
for use with NXA-MTC/RGB
)
75mm x 75mm
VESA mounting configuration
Cable routing hole
(accepts Strain Relief Grommet)
Vents
front
FIG. 2
Location of the attachment screws on the NXD back box
Unscrew these
4 pan-head Housing
DO NOT
REMOVE
these
(panel
securing)
screws
screws to remove the
back box
DO NOT
REMOVE
these
(panel
securing)
screws
