Ampetronic FSM Скачать руководство пользователя страница 1

Handbook Contents 

 

Safety 

 

Introduction 

 

Overview of unit 

 

Operation of unit 

 

Signal cables 

 

 

 

AFILS Test / Commissioning 

Procedure 

1. 

Volume of use 

2. 

Background Noise 

3. 

Field Strength 

4. 

Frequency Response 

5. 

Field Strength 

6. 

Overspill 

7. 

System use 

 

Troubleshooting 

 

Technical Specifications 

 

Accessories 

 

Warranty & Calibration 

 

Declaration Of Conformity 

 

Basic Commissioning procedure 

 

Test CD track listing 

Box Contents 

1 x FSM 
2 x Batteries 
1 x Pouch 
1 x CD of test signals 
1 x ‘User Handbook’ inc AFILS Test / 

Commissioning Procedure 

1 x ‘Designing Induction Loops 

Handbook’ 

1 x Certificate of conformity 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

 
This symbol is used to alert the user to important 
 operating or maintenance instructions. 

 

 The Lightning bolt triangle is used to alert the user 
 to the risk of electric shock. 

 
SAFETY 

1. 

It is important to read these instructions, and to follow them. 

2. 

Keep this instruction manual in an accessible place. 

3. 

Clean only with a dry cloth. Cleaning fluids may effect the equipment. 

4. 

Refer all servicing to qualified personnel. Servicing is required when the apparatus has been 
damaged in any way, such as a power supply cord or plug is damaged, liquid has been spilled 
or objects have fallen into the apparatus, the apparatus has been exposed to any rain or 
moisture, does not operate normally or has been dropped. 

5. 

 

WARNING – To reduce the risk of fire or electric shock, do not expose this apparatus 
to rain or moisture. The apparatus shall not be exposed to dripping or splashing and no 
objects filled with liquids, such as vases, shall be placed on the apparatus.

 

 

TO PREVENT ELECTRIC SHOCK DO NOT REMOVE THE 
COVER. THERE ARE NO USER SERVICABLE PARTS 
INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL

.

 

Содержание FSM

















Отзывы: