Installation Instructions
12/24 volt receiver & keyfob upgrade kit type AP433-RX1
AP433-RX1 receiver & AP433-TX4 keyfob
Positioning
The receiver unit should be secured in a dry position using the
self-adhesive pads supplied. If used with gate equipment it
must be housed in a weatherproof plastic enclosure as the
receiver is not water resistant.
Power Requirement
operating voltage range: 9 - 30 volts AC or 10 - 35 volts DC
nominal standby consumption < 5mA
Connections
Red wire: AC or DC power source (see above)
Black wire: ground (power source)
Blue wires: Volt free relay contact for direct connection to the
‘impulse’ control circuit of a gate or garage door operator. (max
load 1A)
Terminated with four wire ends
Typical Applications
Suitable for use with remote controlled garage door
and gate operators with a 12 - 24 volt power source
for ancillary equipment.
Digital code system
The keyfob transmitters communicate with the receiver by
rolling code digital 433Mhz radio transmission. The receiver
can learn & memorize the unique security code signature of
up to 25x keyfob buttons
Transmitter Compatibility
Only AP433-TX4 rolling code transmitters or the
following alternative 433Mhz transmitters can
be programmed to the AP433-RX1 receiver:
BFT MITT02 & MITT04, Fadini Jubi F/J2T & F/J4T,
Gibidi AU01600 & AU01680, AU03000 & AU03010
Seip SKR series, Sentry SEN-H-T1 & SEN-H-T3
Transmitter battery replacement
Remove the three screws from rear and remove the
casing to reveal a 12 volt battery type GP27A (or LR27A)
Range - up to 100Mtrs
433Mhz MPT 1340 UK approved frequency
Electrical connections for use with popular UK garage door operators
The AP433-RX1 receiver unit is supplied with coloured wires, connect these wires
to your garage door opener unit as follows: (A small screwdriver is provided)
Operator Make & Model
Impulse connections
(blue wires)
12-24 Volt power source
(red & black wires)
Cardale DC550N, DC650N,
DC800N
Connect one blue wire from the new receiver to
terminal 3 & one blue wire to terminal 4
Connect black wire from the new receiver to terminal 7
(0 volts) and connect red wire to terminal 5 (24 volt supply)
Henderson/Sommer Marathon
S550N
Connect one blue wire from the new receiver to
terminal 2 & one blue wire to terminal 3
Connect black wire from the new receiver to terminal 15
& connect the red wire to terminal 16 (24 volt supply)
Henderson/Sommer Sprint
S550N & Duo 650N
Connect one blue wire from the new receiver to
terminal 5 & one blue wire to terminal 6
Connect the red wire from the new receiver to terminal 1
& connect the black wire to terminal 2 (24 volt supply)
Seip APM60, APM80, UK60,
UK80
Connect the blue wires to terminals C & D
Connect black wire to terminal 3 & red to terminal 4
Seip ST60, ST77M, ST77,
ST100
Connect the blue wires to terminals C & D
Connect black wire to terminal 7 & red to terminal 8
Seip A45, A60
Connect the blue wires to terminals C & D
Connect black wire to terminal 12 & red to terminal 13
Seip M50 C75, C100
Connect the blue wires to terminals A & B
Connect black wire to terminal G & red to terminal H
(c) Copyright 2012
Amourelle Products Ltd
United Kingdom
-
phone: 0118 969 4657
Further information can be found on our website:
www.garage-door-remotes.co.uk/ap433-rx1-fit.htm
