15
ARR 1575
WORKSHOP MANUAL
Safety measures for work on hydraulic circuits
•
Before disassembly, make sure the hydraulic circuits are depressurized. Hydraulic oil leaking under pressure may damage your skin
and cause serious injury.
•
Before disassembly, mark the parts, hoses and pipes.
•
Do not put hydraulic pumps and motors into operation without oil.
•
Work with hot oil may result in scalding.
•
Do not heat the oil to temperatures above 160 °C – the oil or its vapours may ignite.
•
When removing hydraulic components, always blank off the hose ends and outlets of the components.
•
Use lint-free cloth when wiping and cleaning hydraulic parts.
•
When assembling parts, use hydraulic oil as a slip agent – not lubricating grease.
•
Before installation, carefully clean the fittings and flush and blow compressed air through hoses and pipes.
•
Only use new seals.
•
Fill new aggregates with hydraulic oil before installation.
•
After a hydraulic aggregate replacement, flush the hydraulic circuit and clean the hydraulic tank.
•
Replace the oil filter cartridge.
•
Fill the hydraulic circuit with clean oil of prescribed viscosity, only when the engine is off!
•
Wipe any overflowed oil.
•
Check the connections for any leaks before the system pressurizes.
•
Check all connections after finishing all work.
•
Do not adjust safety valves.
•
After finishing work, reinstall all protective elements.
Check after putting into operation
•
Oil level in the hydraulic tank.
•
Check the charge pressure of replaced hydraulic pumps and the pressure of safety valves.
•
Perform the measurement at 40 °C (104 °F).
Safety measures for work on the fuel system
Petrol and diesel mixtures (winter fuel) are as flammable as petrol.
- Do not refuel in enclosed spaces.
- Wipe any overflowed fuel.
- Do not smoke and do not use an open flame while working on the fuel system! There is a risk of fire!
Содержание ARR 1575
