Ammann 5953002 Скачать руководство пользователя страница 131

Страница: 131 / 194

125

ARX 36-2 T4i, ARX 40-2 T4i , ARX 45-2 T4i

595026

595038

282N116T

MAINTENANCE MANUAL

3.6.12 Checking the fan and engine belt

for condition

Fan wear check

Check the fan visually. Replace the fan if damaged (e.g. missing

parts of materials, cracks, shape changes, etc.).

Fan

Order number: 1185010

Belt wear check

Visually inspect the belt.
Cracks perpendicular to the belt width are not considered to

be a fault. If longitudinal cracks appear on the belt, or the belt

edges are ragged, or some material parts are pulled off, then the

belt must be replaced.

Belt tension check

Press with your thumb at the spot where the belt length be-

tween the pulleys is the longest, use the force of 98 N (22 lb).

The max. slack (A) is 7–9 mm (0.28–0.35 in).
Tighten the belt (1) by loosening the screws (2) and shifting the

alternator (3) if required.
Check the belt for correct tension.

Check the fan wear, belt wear and tension with the en-

gine off.

Содержание 5953002



































































































































































































Результаты поиска

Содержание 5953002

Отзывы:

Ammann 5953002, Руководство по эксплуатации, Страница: 131 / 194

Результаты поиска

Содержание 5953002

Отзывы: