Ammann 5953002 Скачать руководство пользователя страница 127

Страница: 127 / 194

121

ARX 36-2 T4i, ARX 40-2 T4i , ARX 45-2 T4i

588045

588046

3-5

615084

615083

MAINTENANCE MANUAL

3.6.8 Sprinkling tank refilling

Check the water level in the tank in the inspection hole.

Open the tank cap and refill with clean water.

Before the winter period, drain the water from the water

tank and from the sprinkling system!

3.6.9 Scraper adjustment

Fixed scrapers (optional equipment)

Loosen the screws and move the scraper so that it is in contact

with the drum.

Hinged scrapers (optional equipment)

The hinged scrapers can be lifted and lowered manually. Before

driving adjust the drum scrapers and move the scraper so that it

is in contact with the drum.

Scrapers for the wheel axle

Adjust the tyre scrapers so that there is a gap of 3–5 mm be-

tween the scraper and the tyre.
Never wipe off the emulsion.

Содержание 5953002



































































































































































































Результаты поиска

Содержание 5953002

Отзывы:

Ammann 5953002, Руководство по эксплуатации, Страница: 127 / 194

Результаты поиска

Содержание 5953002

Отзывы: