Ammann 5953002 Скачать руководство пользователя страница 113

Страница: 113 / 194

107

ARX 36-2 T4i, ARX 40-2 T4i , ARX 45-2 T4i

2152

MAINTENANCE MANUAL

Water quality

Do not use hard water with a higher content of calcium and

magnesium, which brings calculus formation, and with a higher

content of chlorides and sulphates, which causes corrosion.
The maximum content of compounds of calcium and magne-

sium is 170 milligrams – hardness of water.
The maximum content of compounds of chlorine is 40 milli-

grams.
The maximum content of compounds of sulphur is 100 milli-

grams.

Safety instructions:

1)  Protect your hands with protective gloves.
2)  In case of ingestion immediately seek medical treatment.
3)  In case of contact with skin or clothing immediately wash

the affected area with clean water.

4) Do not mix different types of coolants. The mixture can

cause a chemical reaction with formation of harmful sub-

stances.

3.2.3 Coolant

The coolant specification must meet requirements of:

- SAE J1034
- SAE J814c

To fill the cooling circuit, use the coolant in the mixing

ratio of 50%/50% with high-quality water (thermal pro-

tection up to -37°C).
Change the coolant every 2 years at the latest.

Note

The machines are filled with a cooling solution with the Bantleon

Avia Antifreeze NG coolant, specification SAE J 1034 at the manu-

facturer's during the production.
It is a coolant based on monoethylene glycol containing silicates.

Nitrite- amine- borate- and without phosphates.
There is an Avia NG label placed where the coolant is to be filled

into the machine.

Refill the cooling circuit with the same or a completely

miscible coolant of the required specification.
If the use of a different, immiscible coolant is neces-

sary, the cooling circuit must be completely drained and

cleaned with clean water repeatedly, at least 3 times.

However, it is not allowed to use a coolant of a different

specification than stated by the engine manufacturer.
The coolant protects the cooling system from freezing,

corrosion, cavitation, overheating etc.
It is forbidden to operate the machine without coolant

even for a short time.
It is forbidden to use a coolant of a different than pre-

scribed specification and base. The engine and the cool-

ing system can get damaged and the warranty lost.
Always check the ratio of antifreeze cooling agent in the

coolant with a refractometer before the winter season

starts.

Содержание 5953002



































































































































































































Результаты поиска

Содержание 5953002

Отзывы:

Ammann 5953002, Руководство по эксплуатации, Страница: 113 / 194

Результаты поиска

Содержание 5953002

Отзывы: