manualshive.com logo in svg

Ametek SPECTRO ARCOS FHX22, Оригинальная инструкция по эксплуатации

Поделиться
Скачать
Ametek SPECTRO ARCOS FHX22 Скачать руководство пользователя страница 40

 
 

Maintenance 

 

 

 

 

— 40 

SPECTRO ARCOS FHX22 — 18.07.2019 

 

 

6. 

The OPI has a latch (1), which is 
released by moving it upwards 
(2). 

7. 

Carefully pull the OPI at the 
handle (3) to the front (4). 

8. 

Remove the OPI from the torch 
housing.  

 

Removal of the OPI is now 
complete. 

 

Fig. 15 

 

6.8.2 

Cleaning the sampler 

In order to clean the sampler, proceed as follows: 

 

1. 

Unscrew the sampler (2) from 
the OPI (1), using the OPI tool 
(3).  

 

Hold the front side of the 
OPI down. This prevents 
dirt particles from falling 
into the OPI. 

 

Fig. 16 

2. 

Clean the sampler under running water using a nailbrush.  

 

When heavy contamination must be removed, a suitable acid may be 
used. Then flush the sampler thoroughly with distilled water.  

3. 

Clean the sampler opening, e.g. using a pipe cleaner. 

4. 

Let the sampler dry by the jet of air or argon.  

5. 

Reinstall the sampler (2).  

 

Cleaning of the sampler is now complete. 

 

 

1

3

2

4

Содержание SPECTRO ARCOS FHX22
























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды