manualshive.com logo in svg

Ametek SPECTRO ARCOS FHX22, Оригинальная инструкция по эксплуатации

Поделиться
Скачать
Ametek SPECTRO ARCOS FHX22 Скачать руководство пользователя страница 13

 

 

 

 

 Safety 

 
 
 

 

SPECTRO ARCOS FHX22 — 18.07.2019  

— 13 

 

 

2.5 

Residual risks 

 

This instrument has been manufactured in accordance with the latest state-of-the-
art technology. Residual risks cannot be completely excluded, however. 

 

 

Warning! Risk of injury and health hazard! 

 

Hazardous sample residues may be present in the sample introduction 
system and waste containers. 

 

Take suitable safety precautions before working on it. 

 

Observe the safety data sheets as well as the H and P phrases that apply 
to the sample material and/or the solvent used. 

 

The content of the UV Plus purifier is a hazardous substance. 

 

The associated material safety data sheet is available at 
http://MSDS.spectro.com. 

 

 

Warning of toxic substances! 

 

Vapors may be generated from the sample material. These may be toxic 
and/or corrosive. 

 

In these cases, provide protective measures, e.g. breathing apparatus 

 

The sample material may be toxic and/or corrosive. 

 

Ensure that the sliding door is closed during the operation. 

 

Ensure that the external exhaust system functions properly. 

 

The cooling system contains a coolant. 

 

The associated material safety data sheet is available at 
http://MSDS.spectro.com. 

 

 

Warning! Hot surface! 

 

The plasma torch, plasma interface and load coil heat up during operation. 

 

Always let the components cool down before working on them. 

Содержание SPECTRO ARCOS FHX22
























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды