background image

SG Series Programming 

SCPI Command Operation 

M550129-03 Rev L

 

6-5

 

6.2.4

 

Operation Status and Questionable Status 
Registers 

The  Operation  Status  and  Questionable  Status  Registers  will  always 
return  0  when  queried.    The  Operation  Status  Enable  and  Questionable 
Status  Enable  Registers  can  be  programmed  and  queried  to  allow  SCPI 
compatibility but have no effect on the Operation Status and Questionable 
Status Registers. 

6.2.5

 

Error/Event Queue 

The  Digital  Interface  Adapter  (DIA)  maintains  an  Error/Event  Queue  as 
defined  by  SCPI.    The  queue  holds  up  to  10  error  events.    It  is  queried 
using  the  SYSTem:ERRor?  command  which  reads  in  a  First  In/First  Out 
(FIFO)  manner.    The  read  operation  removes  the  entry  from  the  queue.  
The *CLS command will clear all entries from the queue. 

The following error codes are defined in the SCPI 1995.0 specification and 
are  supported  by  the  DIA.    Error  codes  are  in  the  range  of  [-32768, 
32767].  SCPI reserves the negative error codes and 0, while error codes 
greater than 0 are device specific errors. 

Table 6-4 Table 6-5.  SCPI Error Codes 

Error Code  Description 

206 

No channels setup to trigger 

This means that an attempt was made to trigger the DIA using the 
TRIG:TYPE <1|2|3> command when there are no armed trigger settings.  
This error is 

not

 generated when the GET is received, even when there are 

no armed trigger settings. 

205 

GPIB GET not allowed during message 

This error means that the GPIB G(roup) E(xecute) T(rigger) multiline 
command was errantly generated by the system computer while or very 
shortly after a message is or was sent.  Give a few milliseconds after a 
message was sent before attempting a GET; and never send a GET during 
the midst of a message transfer over the GPIB. 

204 

GPIB IFC caused warm boot 

This error relates to the GPIB IFC signal, and is available only in 
association with a proprietary command. 

203 

Hardware watchdog warm boot 

This error is caused by a hardware fault either in the power supply proper, 
or on the DIA.  One possible explanation might be that the mains power to 
the supply was interrupted for a short but sufficient time to cause the DIA 
processor to reset and re-boot.  Also, it might be possible to generate this 
error by a very momentary off action of the front panel power switch. 

202 

Foreground watchdog warm boot 

This error means that the internal firmware on the DIA found an internal 
error condition that halted processing; to force resumption of processing, a 
warm boot was required. 

Содержание Sorensen SG Series






















































































































































Отзывы: