Amersham Biosciences Hoefer DALT Скачать руководство пользователя страница 53

Страница: 53 / 70

Hoefer DALT System

Gradient Gel Solutions

Amersham Biosciences

Gradient Gel Solutions

The concentrations of APS and TEMED in gradient solutions vary to assure top-down

polymerization. We suggest: for light solutions, 0.025 – 0.09% (v/v) TEMED and

0.1% (w/v) APS; for heavy solutions 0.0071 – 0.0028% (v/v) TEMED and

0.05% (w/v) APS. The amounts of TEMED and APS suggested here are based on our

experience. You may want to change these volumes for your lab because of differences

in temperature and reagent quality.

Perform a small-scale test before first using a new composition to check that your light

solution polymerizes in about 10 minutes and your heavy solution in about 20 minutes.

Vary the TEMED concentration to control the rate of polymerization.

Note that the light mix is always assumed to have a lower acrylamide concentration

than the heavy mix; the gradient increases in %T from top to bottom. These solutions

can be degassed, though this is not usually necessary.

Light Solution, 1000 ml.

Amounts shown in ml.

Heavy Solution, 1000 ml

Amounts shown in ml.

Final %T

Acryl. Stock

233

267

300

333

367

400

433

467

500

533

567

600

633

1.5M Tris-Cl,
pH 8.8

250

Water

494

461

428

395

362

329

295

262

229

196

162

129

10% SDS

Glycerol

10% APS

10.00 10.00 10.00 10.00 10.00 10.00 10.00 10.00 10.00 10.00 10.00 10.00 10.00

10% TEMED

2.45

2.14

1.90

1.71

1.55

1.43

1.32

1.22

1.14

1.07

1.01

0.95

0.90

Final %T

Acryl. Stock

267

300

333

367

400

433

467

500

533

567

600

633

667

1.5M Tris-Cl,
pH 8.8

250

Water

400

366

333

300

267

233

200

167

133

100

10% SDS

Glycerol

10% APS

5.00

10% TEMED

0.71

0.64

0.57

0.52

0.47

0.44

0.41

0.38

0.35

0.34

0.32

0.30

0.28

Содержание Hoefer DALT







































































Результаты поиска

Содержание Hoefer DALT

Отзывы:

Amersham Biosciences Hoefer DALT, Руководство пользователя, Страница: 53 / 70

Результаты поиска

Содержание Hoefer DALT

Отзывы: