background image

RECOMMENDED TOOLS AND MATERIALS

Putty Knife

Regular Screwdriver

Adjustable Wrench

Sealant

Tape Measure

Hacksaw

Wax Ring/Gasket

Flexible Supply Tube

Closet Bolts

Carpenters Level

1

   REMOVE OLD TOILET

a.

Close toilet supply valve and flush tank completely.  Towel or sponge remaining water from tank and bowl.

b.

Disconnect and remove supply line.  NOTE:

 If replacing valve, first shut off main water supply!

c.

Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.

d.

Remove closet bolts from flange and clean away old wax, putty, etc. from base area.
NOTE: 

 Mounting surface must be clean and level before new toilet is installed!

INSTALL CLOSET BOLTS
Install closet bolts in flange channel, turn 90

°

, and slide 

into place 6" (152 mm) apart and parallel to wall.

SAVE FOR FUTURE USE

3

2

CLOSET FLANGE

CLOSET BOLTS

7 3 0 4 4 9 - 1 0 0   R e v .   C

12"

(305mm)

Saniwares

   

CAUTION:  PRODUCT IS FRAGILE.  TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!

P r o d u c t   n a m e s   l i s t e d   h e r e i n   a r e   t r a d e m a r k s   o f   A m e r i c a n   S t a n d a r d   I n c .
©   A m e r i c a n   S t a n d a r d   I n c .   2 0 0 2

 

!

NOTE:  

Pictures may not exactly define contour of china and components.

HERITAGE1.6 GPF ONE-PIECE TOILET
2071.016

ROUGHING-IN DIMENSIONS:  
NOTE: 

 Distance from wall to closet flange centerline must be as listed below:

Thank you  for selecting American Standard - the benchmark of fine quality for over 100 years.  To ensure this product 
is installed properly, please read these instructions carefully before you begin. (Certain installations may require 
professional help.) Also be sure your installation conforms to local codes.

INSTALLATION

INSTRUCTIONS 

5

4

INSTALL WAX SEAL
Invert toilet on floor (cushion to prevent damage), and 
install wax ring evenly around waste flange (horn), with 
tapered end of ring facing toilet.  Apply a thin bead of 
sealant around toilet base.

POSITION TOILET ON FLANGE
a.

Unplug floor waste opening and install toilet on closet flange so bolts project
through mounting holes.

b.

Loosely install retainer washers and nuts. Side of washers marked "THIS
SIDE UP" 

must face up!

WAX RING

SEALANT

FINISHED WALL

C/L OF OUTLET

C/L OF SUPPLY
AS REQUIRED

FINISHED
FLOOR

30"

(762mm)

4" 

 (102mm)

12"

(305mm)

14"

(356mm)

24-1/2"

(622mm)

19-3/4"

(502mm)

C/L

WASHER

NUT

BOLT

MTG. CLIP

FLANGE

Содержание Heritage Elongated One-Piece Toilet 2071.016

Страница 1: ... o f A m e r i c a n S t a n d a r d I n c A m e r i c a n S t a n d a r d I n c 2 0 0 2 NOTE Pictures may not exactly define contour of china and components HERITAGE1 6 GPF ONE PIECE TOILET 2071 016 ROUGHING IN DIMENSIONS NOTE Distance from wall to closet flange centerline must be as listed below Thank you for selecting American Standard the benchmark of fine quality for over 100 years To ensure ...

Страница 2: ... parts must be used as illustrated to insure water tight connection Use of existing coupling nut may result in water leakage Water supply tube or pipe must extend at least 1 2 inside threaded shank of valve does not apply to flanged tubing Use existing coupling nut and washer Use existing spiral cone washer Fluidmaster cone washer may not seal completely on spiral type supply line Captive cone was...

Страница 3: ...cause leakage and property damage American Standard shall not be responsible or liable for any tank fitting damage caused by the use of cleaners containing chlorine calcium hypochlorite ADJUSTABLE HEIGHT Turn on water supply Adjust water to desired level by squeezing water level adjustment clip and moving FLOAT CUP up or down along stainless steel link FLUIDMASTER TANK COVER SEAT AND COVER FLAPPER...

Страница 4: ...ipe and or vent c Remove obstruction Consult a plumber if necessary d Supply pressure too low d Normal supply pressure must be at least 20 psi Toilet leaks a Poor supply line connection a Review Step 8 of installation procedure Toilet does not shut off a Flush valve chain too tight holding flush valve open a Readjust chain length as needed Review step 9 b Flush valve seat and or flapper worn or de...

Отзывы: