background image

StorTrends® 3600i/3610i Dual Controller IP-SAN Storage Appliance Setup Guide 

Page 14 

 

 

 

Installing  the Outer Rack Rails into the Rack 

 
Locate  the front  of the outer rack  rail  and attach it to the rack.  To do this, simply  push the 
outer rack  rail  into the back of  the rack  post. The plastic securing pins will  retract so that 
you can  latch the outer rack rail  into place. Once the outer rack rail  is latched into place 
the securing plastic pins will  pop back  out. 
 

Quick Rail  Instalation 

 

 

 
Sliding  the rear  of the outer rack  rail  until  it comes  into contact with  the back  post. Make 
sure that the  outer rack  rail  is  level  and  secure it  to  the port  in  the same  manner  as  you did 
with  the front of the outer rack  rail. 
 
Secure  the outer rack  rail  to the rack  posts with four screws. Two  for  the front post and 
two for  the rear  post. 
 
Repeat this process with the remaining  outer rack  rail. 
Line  up the inner  rack  rails  of  the chassis with the outer rack  rails  on the rack. 
 
Slide  the chassis into place until  it  comes to a stop. 
Verify  that both sides of the chassis come to a stop at the same  location.   
 
Lift  the  locking  tab  on  the inner  rack  rails  so that you can  slide  the chassis all  the  way 
into the rack. 

 

Содержание StorTrends 3600i





































































































Отзывы: