background image

 

August 18, 2003 

INSTALLATION, OPERATION AND MAINTENANCE 

INSTRUCTIONS FOR THE AMI

 

MODEL 150A

 

LIQUID HELIUM LEVEL METER

 

I.

 

INTRODUCTION 

The American Magnetics, Inc. (AMI) Model 150A is a compact, fully portable Liquid Helium 
Level Meter providing simple and easy operation.  The instrument is battery operated and when 
used in conjunction with an AMI LHe Level Sensor, provides a truly portable means of 
measuring liquid helium levels at any location.  The sensor connects to the instrument via a 
standard DB9 connector.  The instrument displays 0-100% of sensor maximum active length 
immersed in LHe.  The instrument can be used with AMI sensors with active lengths of up to 60 
inches.  The instrument is powered by sealed lead-acid batteries.  A standard AC-DC adapter 
(either 120VAC or 230VAC) is supplied with the unit for charging the batteries.  Since battery 
energy consumption is strongly dependent on the LHe level being measured, AMI has developed 
a special "battery saver" circuit which reduces the power drain from the batteries as more of the 
sensor becomes superconducting. Power requirements decrease as LHe level increases.  A front 
panel POWER LED is provided to indicate sufficient battery power exists to make an accurate 
level reading. 

The CE mark applies to the handheld unit and the European AC adapter.  The North American 
AC adapter is not CE marked. 

II.

 

SPECIFICATIONS (at 25 °C unless stated otherwise) 

Input Power (instrument) 

Sealed lead-acid battery (6VDC)

 

Input Power (AC adapter)

 

90VAC to 132VAC 50/60 Hz, or 180VAC to 264VAC 
50/60 Hz  (depending on specified AC adapter model) 

Operating temperature (instrument)

 

0 to 50 °C non-condensing

 

Operating temperature (AC adapter)

 

0 to 40 °C non-condensing

 

Sensor active length range 

1 inch to 60 inches 

Linearity

 

0.5% of full scale

 

Absolute Calibration

 

0.5% of full scale 
2% of full scale (from 0 to 50 ºC)

 

Probe Current

 

75 mA nominal

 

Battery Life

 

Typically 1,000 readings with a 60" sensor.

 

* Under extreme radiated electromagnetic field conditions (3V/m @ 80MHz to 1GHz) the 
accuracy may be degraded by an addi/- 1.2% 

Содержание 150










Отзывы: