Page 1 of 2
11775 E. 45th Ave. Denver, CO 80239 Ph: 1-800-880-1180 Fax: 303-695-7633
©2019 American Lighting, Inc. REV1946 www.AmericanLighting.com
MICROLUX
STATIC WHITE
24V
INSTALLATION INSTRUCTIONS
MLUX-30 & MLUX-40
SAFETY INFORMATION
• Read all installation instructions before beginning; if not qualified, do not
attempt installation. Contact a qualified electrician.
• To reduce the risk of fire, electric shock, or injury to persons, pay close
attention to this manual and stay within its guidelines when using this
product. Save these instructions for future use.
• Do not cover this product as the covering may cause rope to overheat,
melt, or ignite.
• Uncoil flexible light prior to plugging in. Do not operate Microlux on the
reel, nor while it is coiled.
• This IP65 rated flexible light is suitable for wet locations, but not
intended for submersion. Do not submerge flexible light in liquids, or use
the product in the vicinity of standing water or other liquids, or where
water can accumulate. IP65 rating is void once product is cut.
Cut product is rated IP54 and intended for indoor, dry locations only.
• Do not route the cord or flexible light through walls, ceilings, doors,
windows, or any similar part of the building structure.
• Do not install on gates or doors, or where subject to continuous flexing.
• Do not install in tanks or enclosures of any kinds.
• Do not install near flammable liquids or other flammable materials.
• Secure flexible light using only the mounting clips (MLUX-CLIPS)
provided or factory recommended mounting track (MLUX-CHAN)
(sold separately).
• Do not secure this product or its cord with staples, nails, or like means
that may damage the outer jacket or cord insulation.
• Do not use if there is any damage to the flexible light, diodes or power
cord insulation; inspect periodically.
• Follow instructions carefully when cutting MicroLux. Ensure all end caps
and cut locations are properly sealed with appropriate silicone or PU
type glue. 24V MicroLux can only be cut at specific intervals as indicated
by the cutting marks printed on the bottom of the PU housing (1.31” or
3.3mm). Failure to cut at a cut mark will result in a loss of light. Before
making any cuts or attaching any power cords or jumpers, be sure power
is disconnected at the source!
• This product is designed for use by a qualified installer.
• This product is for decorative use only. Not to be used by children as a
toy. Keep out of reach of small children.
• Do not exceed 5 meters or 16.4 feet maximum run distance in any single
inter-connected run.
• Size your 24V DC driver appropriately for your run distance. Be sure not
to load a driver to 100% as this will reduce its efficiency; a 90% maximum
load is recommended. Recommended drivers include ADPT-DRJ, LED-
DR, and ELV series.
• The rated ambient temperature range for NeoFlux is -30°C (-22°F) to
45°C (113°F). Freezing temperatures may cause product rigidity.
These products may represent a possible shock or fire
hazard if improperly installed or attached in any way.
Products should be installed in accordance with these
instructions, current electrical codes, and/or the current
National Electric Code (NEC).
Use this fixture with included connection kit and 24V DC
power supply only. Any other power feed may damage
the fixture. Factory warranty will be void if used with
any driver other than the recommended driver series.
To reduce the risk of fire, electric shock or injury to
persons, use this flexible light only with American Lighting
recommended drivers, controllers, power connectors,
splices and extensions.
To reduce the risk of fire, electric shock or injury to
persons, make sure that the electrical power to the
system is disconnected at the source prior to installation
or any servicing.
The minimum bend radius of MLUX-30/40/RGB series
product is 12cm or 4.7”. Do not twist, drop, hang, sag,
or bend product in any way other than intended. See
below for reference. Never fold Microlux or bend past the
minimum bending radius whether lighted or unlighted.
When using outdoor portable lighting products,
basic safety precautions should always be followed
to reduce the risk of fire, electric shock, and
personal injury, including the following:
• Use dielectric grease and shrink tube at all power
connections, including end cap when using outdoors.
• Use ground fault circuit interrupter (GFCI) protection
on the circuit(s) or outlet(s) when using outdoors.
• Use only UL approved outdoor extension cords, such
as type SW, SOW, STW, STOW, SJW, SJOW, SJTW, or
SJTOW. This designation is marked on the jacket of
the extension cord.
WARNING
WARNING
WARNING
WARNING
WARNING
PRODUCT INFORMATION
Microlux 16.4ft reels include (1) attached 3ft power connector with bare wire leads and mounting clips with screws.
Mount microlux using clips (MLUX-CLIPS, included or sold separately) or channel (MLUX-CHAN-3A or MLUX-CHAN-3B, sold separately).
Additional accessoriesfor MicroLux static white include a splice kit (MLUX-SPL2), 6 foot linking jumper (MLUX-JUMP2-.5), a 12” linking jumper
(MLUX-JUMP2-2), end caps (MLUX-END), mounting clips (MLUX-CLIPS), and mounting channel (MLUX-CHAN-3A full profile or MLUX-CHAN-3B
half profile), all sold separately.
Do not operate
MicroLux while it is
coiled or on the reel.
Do not hang
Do not
droop or sag
CARE AND MAINTENANCE:
1. For cleaning, use a soft, dry or damp cloth. Do not use harsh chemicals or abrasives.
