SAFETY INFORMATION
• Read all instructions before beginning. Save these instructions for future use.
• To reduce the risk of fire, electric shock, or injury to persons, pay close attention to this
manual. Stay within its guidelines when using this product.
• All units must be unplugged before installing or servicing in any way.
• Do not route cords or units through walls, doors, windows, or any similar part of a
building structure.
• Do not use if there is any damage to the unit, its lens, and/or power cord’s insulation.
Inspect periodically.
• Controller housing is suitable for outdoor use (rated IP44), however when usign
outdoors, all power, DMX, and/or output connections must be properly sealed with shrink
tube and silicone and/or housed in a weather proof enclosure.
• Do not let the unit stand in water or liquid, nor locate where water can accumulate.
• Secure units with mounting hardware appropriate for the mounting surface. Do not
secure unit or its power cord with staples, nails, or like materials that may damage
insulation.
• Do not attempt to open or service this fixture. None of its parts are seviceable by the user.
• This product has a polarized, grounded plug as a safety feature. Do not cut the plug off
or alter it in any way.
• Provide a grounded receptacle for within 5 feet of each fixture’s location. If using
outdoors, outlet(s) must also be GFCI and weatherproof.
• Operating temperature must be between 20°C and 45°C (-4°F and 113°F). Avoid high
ambient temperatures.
• This controller requires the use of LED-RGB-15A-24V, 24V DC 15A power supply. Do not
operate this controller with any other power supply.
• Do not exceed more than 88ft of RGB-NF total on controller (maximum single run for
RGB-NF is 65ft)
These products may represent a possible shock or
fire hazard if improperly installed or attached in any
way. Products should be installed in accordance with
these instructions, current electrical codes, and/or the
current National Electric Code (NEC).
When using this product outdoors, basic safety
precautions should always be followed to reduce the
risk of fire, electric shock and personal injury including
the following:
• Ground Fault Circuit Interrupter (GFCI) protection
should be provided on the circuit(s) or outlet(s) to
be used for outdoor use. Receptacles are available
having built-in GFCI protection for this measure of
safety.
• Use only outdoor extension cords, such as type
SEW, SEOW, SEOOW, SOW, SOOW, STW, STOW,
STOOW, SJEW, SJEOW, SJEOOW, SJTW, SJTOW,
or SJTOOW. This designation is marked in the wire
of the extension cord. Never use with an extension
cord unless plug can be fully inserted.
WARNING
WARNING
DMX RGB Controller for RGB-NF
24V
INSTALLATION INSTRUCTIONS
LED-RGB-CTRL-24V
G
Page 1 of 2
©2017 American Lighting, Inc. REV1743 www.AmericanLighting.com
11775 E. 45th Ave. Denver, CO 80239 Ph: 1-800-880-1180 Fax: 303-695-7633
FIGURE 1
USING LED-RGB-CTRL-24V WITH RGB-NF:
LED-RGB-CTRL-24V requires the use of LED-RGB-15A-24V 24V DC power supply for operation. Disconnect power at the source prior
to operation.
1. Connect the DC “OUT” from LED-RGB-15A-24V to the DC “IN” on LED-RGB-CTRL-24V
2. Connect one of the included adapter cables to the Signal “OUT” on LED-RGB-CTRL-24
3. Follow the wiring guide on the adapter cable to connect to RGB-NF-CONKIT-NP
4. Follow mode instructions on page 2
LED-RGB-CTRL can be linked together by connecting the
Signal “OUT” from first controller to the Signal “IN” on second
controller. When multiple controllers are used, provide each one
with a LED-RGB-15A-24V DC power supply. Do not exceed 65ft of
RGB-NF in a single run, nor 88ft from a single controller. When power
is applied, the default function is that the first controller in the
series will become the master and the rest will become the secondary
followers. The state indicator display screen will display “H” for master
and “C” for secondary followers.
(A) DMX Out
(B) DMX In
(C) Signal In
(D) Signal Out
(E) Grounded power cord
(F) State indicator display
(G) Content level display
(H) Output indicator lights
(I) Power indicator light
(J) Mode select button
(K) Speed select button
